Products

Mikuni high and low-speed adjuster screws with "T" cross bar - extended length for easy adjustment. Absolutely a must when running aftermarket pipes. Fits all 1996-2020 Yamaha Superjet OEM 38mm Mikuni Carburetors.

Part Number: 01-02-544

OEM Yamaha Battery Power Wire Lead. Fits all years Yamaha Superjet, FX1 and Rickter Models.

Part Number: 6R7-82117-11-00

Blowsion Custom Cut Side Rail Turf Kit. Fits all years Yamaha Superjet, FX1, Polaris Octane, Rickter and Kawasaki 650 and 750 Stand up Models. Improve the traction and looks on the side rails of your ski with our custom fit side rail covering kits. Side Rail Turf Kits Include enough material to cover the front bumper, sides, and rear corners of the side rail. Side rail kits bond directly to the fiberglass. All OEM/Stock plastic will need to be removed prior to application of side rail turf kit. For most applications a Quart of Mat Glue is recommended for installation. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.

Part Number: 04-02-324

ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.

Part Number: 03-05-325

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Brand new modified OEM Yamaha 62T Crankcases now available from Blowsion for DASA Big Bore Stock Stroke Engine Setups. Includes Case Bore, Epoxy Fill, Trenching and Reinforcement plate for Stock Stroke Crankshafts.

Part Number: 01-03-763
OEM Yamaha Crankcase Part Number: 62T-15100-00-00

DASA Stroker 89.00mm-95.00mm Pistons now available by Blowsion.

Genuine Mikuni Replacement Check Valve Plate Screw for Mikuni SBN Carburetors. Diagram #37.

Part Number: BV15/121-05-GG

OEM Yamaha 144mm Pump Impeller Housing. Fits all years Yamaha Superjet, WaveBlaster 1 and Rickter Hull Models.

Part Number: 6R7-51312-03-94 / 6R7-51312-03-00

Replacement RRP Trim Cable. Overall Length: 142.00" (Inches).

Part Number: 02-02-514

Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.

Part Number: 01-03-816

ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.

Part Number: 03-05-330

WSM Aftermarket Motor Mount for all Yamaha Superjet Models.

Part Number: 011-115

Stainless steel handle bar clamp screws (4 pack). Fits Blowsion Billet Handle Bar Clamps.

Part Number: 03-05-031

Fits all OEM Yamaha 650, 701 and 760 Models. OEM thickness (0.020"). Replaces OEM Yamaha Base Gasket Part Numbers: 6M6-11351-A1-00, 6M6-11351-A2-00

Part Number: 01-03-323