Products

Blowsion Cross Bar Pad. For use with all 7/8" inch Standup and Sport watercraft handlebars including Blowsion Kommand Bars. Pad measures 5.25 inches in length. Available in all colors!

Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-102

48" x 17.5" section of 9mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.

Part Number: 04-02-328

Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.

Blowsion Kawasaki Big Bore 820cc Ported Engine. Complete Short Block.

Part Number: 01-03-770

Xtreme Grips from ODI. New Graphite Grey Grip design. Starter kits come with Carbon Silver ODI Lock On Clamps and ODI’s new Snap Cap end caps. These grips feature a tapered knurl pattern that is larger and deeper where you need more traction.

Part Number: 03-05-301

Blowsion Billet 90-Degree Water Bypass fittings. Fits 3/8" ID Cooling Hoses. Offered in Anodized Clear, Black, Green, Red, Blue and Orange. All Colors In stock!

An ultra bitchin' way to keep your rear edge tray mat wrapped and sealed down. Excellent solution to a problem area for all mat installations. Available for all models.

ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.

Part Number: 03-05-324

Billet carb adaptors in stock and available to fit Kawasaki SXR 800 and Late Model (1998-2002) Kawasaki 750 SXi-Pro with dual Mikuni carbs. Required for adapting to aftermarket air filters / flame arrestors. Flange Outer Diameter: 2.75 (inches).

Part Number: 01-02-075

So-Cal originals have teamed up to create a modern day classic waffle grip design. Check out the new Vans® Lock-On Grips by ODI.

Part Number: 03-05-361

Strap and secure your hood to avoid accidental dislodging during freestyle and freeride maneuvers. Replaces stock latch assembly. All mounting hardware included.

Part Number: 04-04-310

Now available! Dakine hardware install kit with glue for installing footstraps. Ultra sanitary and leak proof.

Part Number: 04-02-339

Our new CAS (cool as S*%!) flow valve design prevents water getting in during tail stands, wave jumping, or all out buoy shredding. The new billet flange assembly allows use of our billet exhaust outlet so vain riders can sanitize both sides of the rear of their ski. Fits all years Yamaha Superjet, Kawasaki 650, Kawasaki 750, Kawasaki SXR 800, Polaris Octane, Rickter XFS, Rickter XFR, Rickter EVO, Rickter Edge and Most Aftermarket Hulls.

Part Number: 06-01-022

Want to feel the bottom end of your 750 SXI or SXR 800 snap your neck back? The Jetinetics lightened charging flywheel is the way to go. Retains OEM charging capabilities but lightens the rotating mass for unreal bottom end response.

Part Number: 01-04-208