Products

Introducing the new Blowsion Kawasaki Fuel Pickup. Designed with the option for use as a single, dual and triple pickup this billet beauty is the lowest profile and lightest weight internal fuel filler available. Even with all three pickups in use you can still internally fill using a regular fuel jug hose. Includes all fuel line, fuel pickup filters and installation hardware. Fits all years Kawasaki 750 and SXR.

Billet carb adaptors in stock and available to fit Kawasaki SXR 800 and Late Model (1998-2002) Kawasaki 750 SXi-Pro with dual Mikuni carbs. Required for adapting to aftermarket air filters / flame arrestors. Flange Outer Diameter: 2.75 (inches).

Part Number: 01-02-075

Replace your rear factory hood latch with a billet aluminum BLOWSION latch and ride worry free. Recently updated and re-machined to also fit the Kawasaki SXR 800 and SXR 1500. Also fits all years Yamaha FX1 and all years Yamaha Super Jet. A must for surf and big wave riders, especially those running a BLOWSION pole limiting rope. Requires the stock base locking hardware. Now available in more colors- Anodized Green, Red, Blue, Orange, Clear, Purple and Black!

The all new Universal OVP "Over the Pivot" Sealed Bearing Steering System. Fits all OEM Yamaha and Aftermarket Handlepoles (RRP/UMI/AC). Available in Black, Clear, Blue, Orange, Red and Green bright dip anodized colors!  PLEASE NOTE: The Universal OVP Steering System will only work with Fat Straight, Fat Riser or 4-Degree Fat Bars (sold separately). If you are installing on the OEM Yamaha Pole you will need to make extensive modifications to your OEM Chin pad mounting and location in order to clear the handlebars. The chin pad must be re-located further forward on the OEM Pole. You may want to consider the Standard Blowsion Steering System as it will clear the OEM Yamaha Chin Pad without any modifications.

Strap and secure your hood to avoid accidental dislodging during freestyle and freeride maneuvers. Replaces stock latch assembly. All mounting hardware included.

Part Number: 04-04-310

Now available! Dakine hardware install kit with glue for installing footstraps. Ultra sanitary and leak proof.

Part Number: 04-02-339

Our new CAS (cool as S*%!) flow valve design prevents water getting in during tail stands, wave jumping, or all out buoy shredding. The new billet flange assembly allows use of our billet exhaust outlet so vain riders can sanitize both sides of the rear of their ski. Fits all years Yamaha Superjet, Kawasaki 650, Kawasaki 750, Kawasaki SXR 800, Polaris Octane, Rickter XFS, Rickter XFR, Rickter EVO, Rickter Edge and Most Aftermarket Hulls.

Part Number: 06-01-022

48" x 17.5" section of 9mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.

Part Number: 04-02-328

Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.

Want to feel the bottom end of your 750 SXI or SXR 800 snap your neck back? The Jetinetics lightened charging flywheel is the way to go. Retains OEM charging capabilities but lightens the rotating mass for unreal bottom end response.

Part Number: 01-04-208

We have taken one of the oldest aftermarket products in our industry and refined every element imaginable. Introducing the 2023 Blowsion Pro Throttle Lever. Our new billet adjustable Pro Lever sets the standard for quality, rider comfort and cutting edge design while being proudly manufactured and assembled completely in the USA from 6061 Aluminum. Available for all models. Available in anodized Clear, Black, Orange, Red, Blue, Green, Purple and Teal. Also available as a two finger lever option here.

Flow Control Valve - 3/8" Adjustable Pro Model. This 3/8" valve has been designed to prevent water flow to the waterbox at idle and off idle engine speeds. This allows the craft to be more responsive off the line and around turns. Results are HUGE gains in throttle response. All stainless internal parts. IJSBA race legal. Now Available in all Colors!

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.

Part Number: 06-01-201

The 3/8" Quick Disconnect / Water Restrictor can be used as Quick Disconnect or use one of 3 supplied brass inserts to restrict the flow of water or increase pressure where it is needed. Includes 3 brass restrictors and stainless steel hose clamps. Now Available in all colors!