Products
-
Tiny Tach - Original Model
The Original Tiny tach. Displays total engine run time to assure ON-TIME MAINTENANCE. Unlike elecromechanical devices, TINY-TACH hours accumulate only while engine is running.
Part Number: 06-04-090
Learn More -
Tiny Tach - with Peak RPM Recall
The Tiny Tach RPM memory tachometer will monitor engined on all stand-up models with single or twin cylinders. Used for engines with a spark firing every 180 degrees of the engine crankshaft. Maximum RPM recall feature RPM runs to 19,999.
Part Number: 06-04-091
Learn More -
SE Speedmagic 50mm Ninja Dual Carburetors
S.E - Speedmagic 50mm Ninja Dual Carburetors. 50mm dual carb set straight out of Japan (Sato Engineering). These carbs will support a wide range of applications and are perfect for big-bore motors 900cc plus.
Part Number: 01-02-106
Learn More -
SE Speedmagic Air Filter
Sato Engineering SpeedMagic Air Filter. Newly updated 011 version is stronger and produces more airflow.
Part Number: 01-02-025
Learn More -
Solas Kawasaki Mag Pump/Tilt Combo
Solas 140mm Kawasaki 12 Vane Stainless Standard Pump with Adjustable diameter Drop Nozzle Trim System.
Part Number: 02-02-021
Learn More -
Skat-Trak Impeller - Kawasaki C-75 140MM
Skat-Trak Stainless Steel Impeller for Kawasaki 750 and SXR 800 Models. 140MM C-75MM Hub Swirl.
Learn More -
Skat-Trak Aluminum Pump Shoe - Kawasaki SXR
Maximize water flow into the SXR intake inlet. This aluminum pump shoe works in conjunction with the standard Skat Trak top loader scoop grate, or the Skat Trak cut away model of the same intake grate.
Part Number: 02-05-431
PLEASE NOTE: This product has been discontinued.Learn More -
Blowsion Kustom Cut-Back Stainless Impellers
Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.
Learn More -
Skat-Trak Trim Cable Long (Kawasaki Pulley System)
Skat-Trak Trim Cable Long for Kawasaki Pulley Systems. Fits all SXR 800 trim and tilt systems. Direct replacement for Skat Trak and Blowsion systems.
Part Number: 02-02-543
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
RRP CBX Carbon Handlepole
RRP CBX (Carbon Billet X-Lite) Handlepole. The new CBX is an ultralight carbon fiber and billet aluminum x-lite adjustable handlepole is recommended for freestyle and racing. Available with Anodized Aluminum or Carbon Fiber Tubes.
Learn More -
RRP Threaded Safety Rod
Replacement RRP Threaded Safety Rod for RRP Handlepoles. For use with tubes up to 26 Inches. Nuts not included.
Part Number: 03-04-036
Learn More -
RRP V Riser Fat Bars
RRP Handle Bars available with 50mm Rise. Compatible with 1-1/8" Fat Bar Clamps. Length: 28.6mm
Learn More -
RRP Ninja Chin Pad - White Base
RRP Ninja Chin Pad. Options Available with White Base. Thinner more streamlined design shape! Fits all RRP Cast, RRP Billet, RRP Lightweight Billet and RRP CBX Pole Models. Available in all color options listed.
Learn More