Products

Universal Fuel Pickup Filter. Add some of these for extra fuel filtration and also keeps the fuel in your lines when going upside down.

Part Number: 01-02-449

Billet Aluminum Kawasaki Electrical Box Fittings. Replaces the weak OEM Kawasaki Plastic Electrical Box Fitting (Part Number: 59071-3001) that threads into the stock electrical box. Can be used with OEM Plastic Cap or Billet Aluminum Electrical Box Cap. Threads are 18-1.5mm on the end that goes into the electrical box and 16-1.5mm on the cap side. Includes O-Ring Seal. Fits all Kawasaki JS300, JS440, JS550, 300SX, 550SX, 750SX, 750SXI, 750SXI-Pro and SXR 800 Jet Ski Models. Available in Black, Blue, Green, Red and Orange Anodized Colors.

Properly install and secure your ballistic battery with this foam spacer. Available for all size batteries.

Part Number: 01-04-627

Secure your stand-up's hood to avoid accidental dislodging during freestyle and freeride maneuvers. All stainless mounting hardware and instructions included. Adjustable to fit all models of stand-up PWC.

Part Number: 04-04-301

Direct water and air to where you want it in the engine compartment! Drop Tube and Urethane Flange for Hood Baffle Air Intakes. Use with either aftermarket hoods or stock factory hood to increase air flow. Each kit includes three oversize lengths of hose tubing and urethane flanges. Bond-able to hand laid fiberglass, carbon, SMC or ABS inner liners these are simple to install and are an excellent answer for air-starved motors. An EXCELLENT choice for the Kawasaki SXR 800 with the Factory Pipe installed!

Part Number: 05-02-199

Finish the look of your engine compartment with Blowsion specialty colored 3/8" water cooling hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.

Replacement Blowsion OVP Steering Stem and Nut Kit. Fits OVP Steering Systems for Blowsion Billet Handlepoles.

Part Number: 03-05-047

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Blowsion Two Finger Pro Throttle Lever Only. Compatible with Blowson Pro Throttle Lever Assemblies. Also available in One Finger Version here.

Blowsion Steering System Rebuild kit includes roller bearing, thrust washers, thrust bearing, and large and small O-rings.

Part Number: 03-05-020

The key to installing Tubbie Sponsons, Railcaps and other composite accessories on your watercraft. Easy-to-use tube fits a standard caulking gun. Fast-set formula dries tack-free in 90 minutes and delivers extremely tough bonds. Color: White.

Part Number: 06-03-135

The simple to install stainless and reuseable base gasket, simply clean both mating surfaces and install. Trick. Fits All Years Kawasaki 750 and Kawasaki SXR 800 Models. Thickness: 0.020"

Part Number: 01-03-302

Inline Water Filter. Made from impact resistant nylon with 3/8” barb ends. A clear bowl and removable filter screen allow easy inspection and cleaning.

Part Number: 01-01-780

Fits 6mm choke shaft Mikuni dual carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-406

Replace that cracked and worn out stock plastic battery box with bulletproof Blowsion aluminum. Each box includes all stock location retaining clips for easy exchange. Padded bottom. Direct fit replacement for all years Yamaha Super Jet, FX1 and Polaris Octane. Can be fit as replacement to all Years Kawasaki 750 and SXR 800 with minor battery strap modifications. Color: Anodized Black

Part Number: 01-04-601