Products
-
Bilge Fitting 45-Degree
Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.
Learn More -
Side Rail Turf Kit - Yamaha SJ / FX1 / KAW 650/750 / Rickter
Blowsion Custom Cut Side Rail Turf Kit. Fits all years Yamaha Superjet, FX1, Polaris Octane, Rickter and Kawasaki 650 and 750 Stand up Models. Improve the traction and looks on the side rails of your ski with our custom fit side rail covering kits. Side Rail Turf Kits Include enough material to cover the front bumper, sides, and rear corners of the side rail. Side rail kits bond directly to the fiberglass. All OEM/Stock plastic will need to be removed prior to application of side rail turf kit. For most applications a Quart of Mat Glue is recommended for installation. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.
Part Number: 04-02-324
Learn More -
OEM Yamaha Impeller Housing 144MM
OEM Yamaha 144mm Pump Impeller Housing. Fits all years Yamaha Superjet, WaveBlaster 1 and Rickter Hull Models.
Part Number: 6R7-51312-03-94 / 6R7-51312-03-00
Learn More -
ADA Cylinder Head - Yamaha 701/760
ADA Racing Billet Head Shell for the Yamaha 701/760. All ADA Racing billet heads are made from 6061-T6 aluminum and CNC machined in-house for consistency and performance. The head shell is then anodized for durability and protection against salt-water corrosion. This is the head shell only and includes orings that fit into the grooves in the head shell and brass fittings. Available in Black or Silver.
Learn More -
ODI TLD Grips Pink (130mm)
ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.
Part Number: 03-05-330
Learn More -
Blowsion Pole Bracket Plate
Blowsion Pole Bracket Plate. Required when installing a Blowsion Billet Handlepole on an older (PRE-2014 DESIGN) Blowsion Dual Hole Handle Pole Bracket. Fits 1996-2020 Yamaha Superjet, 1994-1995 Yamaha FX1, 2002-2004 Polaris Octane, and Kawasaki 750 Models.
Part Number: 03-04-067
Learn More -
Mikuni Low Speed Washer
Genuine Mikuni Replacement Low Speed Aluminum Washer for Mikuni SBN Carburetors. Diagram #27.
Part Number: BN38/172
Learn More -
Handlebar Clamp Screw Set
Stainless steel handle bar clamp screws (4 pack). Fits Blowsion Billet Handle Bar Clamps.
Part Number: 03-05-031
Learn More -
ADR Stroker Crankshaft - Yamaha +10mm
ADR Yamaha +10mm (78mm) Stroker Crankshaft with 133mm ADR Rods. ADR performance crankshafts are made from a super strong SCM415 crankshaft steel and go through a strict heat treatment process to control strength and reduce stress. ADR Crankshafts are available for the Yamaha Superjet in +10mm and +16mm stroker options.
Part Number: 01-03-700
Learn More -
Mikuni Throttle Shaft Rebuild 38MM
Genuine Mikuni replacement throttle valve rebuild kit for Mikuni Super BN 38mm Carburetors. MK-BN/038-TV.
Part Number: 01-02-536
Learn More -
Leak Down Block Off Kit Yamaha (62T)
Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.
Part Number: 01-03-816
Learn More -
Mikuni Pop-Off Springs
Mikuni Pop-Off Springs. Available in all sizes. Sold Each. Learn More -
OEM Yamaha Superjet Fuel Tank
Brand New OEM Yamaha Superjet Fuel Tank. Also fits most aftermarket hull applications using Yamaha based platform (Rickter, Krash, Tigercraft, ETC).
OEM Part Number: EW2-67711-01-00
Learn More -
Base Gasket - Yamaha 650/701/760
Fits all OEM Yamaha 650, 701 and 760 Models. OEM thickness (0.020"). Replaces OEM Yamaha Base Gasket Part Numbers: 6M6-11351-A1-00, 6M6-11351-A2-00
Part Number: 01-03-323
Learn More -
PowerFactor Waterbox
The PowerBox was designed to be used with the PowerFactor Exhaust System.Part Number: 01-01-454
Learn More