Products

3.5 Inch Heavy Duty 6 Ply Exhaust Coupler for TNT V2/V3 and PowerFactor Exhaust Systems. Connects Exhaust Manifold to Chamber.

Part Number: 01-01-167

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion Stainless Steel Pump Bolt Kit for Yamaha 155mm Pump Conversions with threaded wear ring. The Socket Head Bolt design allows for use of hex key tool which results in much easier access. Kit Includes 4 Bolts.

Part Number: 02-02-479

Blowsion Dual Cooling Kit for Yamaha Superjet and Polaris Octane Models. Kit includes all hardware and detailed installation instructions. Ultra Sano.

Part Number: 02-02-452

Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.

Part Number: 01-03-816

All metal and stainless construction. Easy to use. Just push in to your 45 degree or 90 degree aftermarket aluminum water bypass(es). Backflush away!

Part Number: 06-04-001

Newly Designed. Easily allows tow watercraft to clip and go. Surf riders and racers are insane to ride without one of these. The ONLY way to effectively guarantee avoiding the next big wave set or the next racer on the course.

Part Number: 04-03-069

New Blowsion OVP "Over the Pivot" steering system. Available in Black, Clear, Blue, Orange, Red, Green and Purple bright dip anodized colors! Specifically designed to fit the new Blowsion Billet handlepole.

Blowsion Custom Cut Mat Kit. Glue it On! Fits all 1996-2020 Yamaha Superjet Models with Klowner Footwells. Includes bottom, tray sides, dash, footwell mat pieces, and undermat foam. Klowner Footwells not included. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.

Part Number: 04-02-077

The design of the Blowsion pole limiting rope is to STOP your pole from extending approx 2-3" from total max extension. This prevents the forward motion of the pole and riders body from destroying expensive handlepoles, pole brackets, hulls and also expensive human body parts!

Part Number: 03-04-151

Blowsion Pro Throttle Lever Only. Compatible with Blowson Pro Throttle Lever Assemblies. Also available in Longer Two Finger Version here.

The preferred choice for fuel filters and water separators. Fits all Yamaha Standups. Can be used also with KAWI and Polaris Octane models. 1/4" Inlet/Oulet hose size.

Part Number: 01-02-551

Blowsion Yamaha Big Bore Ported 760cc Freeride Engine. Complete Short Block.

Part Number: 01-03-756

Billet Handlepole Spacer for the Blowsion Billet Handlepole. Required for riders who prefer a very stiff pole assembly.

Part Number: 03-04-220

Blowsion TNT Exhaust Mounting Block. The foam blocks are designed to hold the pipe in position so that the coupler and stinger height match up perfectly to the manifold and waterbox. Perfect alignment will help optimize performance and increase longevity of the rubber couplers. Kit includes 3 individual foam blocks with 3M adhesive backing. Compatible with all TNT, RRP Carbon and PowerFactor Style Exhaust Systems.

Part Number: 01-01-168