Products

The 1/4" Quick Disconnect / Fuel Restrictor can be used as fuel line quick disconnect and/or for fuel restriction. Pre-tapped and threaded to accept Mikuni Main Jet (Jets not included). Includes stainless steel hose clamps. Now Available in all colors!

Motion Pro Fuel Shut-Off Valve 1/4" Separating Quick Connect (MP#12-0029).

1/8 NPT x 3/8 Barb 90-Degree Brass Elbow Fitting. Used on Most 2-Stroke PWC.

Part Number: 01-01-076

The 3/8" Quick Disconnect / Water Restrictor can be used as Quick Disconnect or use one of 3 supplied brass inserts to restrict the flow of water or increase pressure where it is needed. Includes 3 brass restrictors and stainless steel hose clamps. Now Available in all colors!

If you are looking for a bedding compound with exceptionally strong adhesion, and are not concerned about later removal of hardware, 3M Fast Cure 5200 should be at the top of your list. Along with outstanding adhesion, 3M Fast Cure 5200 remains flexible after it cures and it can be used above or below the waterline. Ideal for underwater thru-hull fittings, hull-to-deck joints, portholes and bonding wood to fiberglass.

Part Number: 06520

3M Marine Grade Silicone creates a rubbery waterproof seal that remains flexible and is mildew resistant. For sealing Lexan™, Plexiglass™, gelcoat, fiberglass, wood, glass, metal, rubber, and vinyl. Cured sealant remains flexible.

Part Number: 08029

ADA Racing Billet Cylinder Head for Kawasaki 650 engines. All ADA Racing billet heads are made from 6061-T6 aluminum and CNC machined for consistency and performance. Anodized for durability and protection against salt-water corrosion. This is the head shell only. Includes orings that fit into the grooves in the head shell and brass fittings. You will need to order domes below under Related Products. When ordering domes, you must order a quantity of 2, as domes are sold individually.

ADA Racing Billet Cylinder Head Dome for Kawasaki 650. Includes compression (OR042) and dome top (OR020) o-rings. Squish relief is .015 inch @ 78mm with a 9.5 degree angle. These domes fit the ADA Racing 650 Cylinder Head. Domes are sold individually.

The Antigravity ATX12-HD-RS is a hi-power lightweight Lithium battery, built with groundbreaking RE-START Technology (built-in jump-starting) so you won’t ever get stranded with a dead battery again! This is the HEAVY DUTY version of the standard duty ATX12-RS, and offers more capacity/cranking power for those who need it.

Part Number: AG-ATX12-HD-RS

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302