Products

MSD 90 Degree Spark Plug Boot Kit.

Part Number: 01-04-410

The RRP Rickter 155mm Aluminum Pump Shoe fits all Yamaha Superjet, 1993-1996 WaveBlaster 1, Rickter and most aftermarket Yamaha based hulls.

Part Number: 02-02-431

ADA Racing Cylinder Head Girdle Kit for Yamaha 701/760 and Yamaha 1100/1200 Girdled Cylinder heads. Includes 6 stainless studs, 6 stainless washers, and 6 chrome acorn nuts. The only true girdle system. It does not bolt the cylinder to the cases, but sandwiches the cylinder between the head and the cases. Therefore, there is no pressure on the base of the cylinder. The threads are rolled for strength and not cut. Thread rolling compresses the material adding strength to the threads. Cutting threads leaves the root of the thread sharp, weakening the thread and making them easier to break.

Part Number: YA701G6

The tried-and-true plunger style primer. In stock and ready to flow!

Part Number: 01-02-410

The RRP Adjustable Hood Latch is made from billet aluminium 6061 t6. This adjustable hood latch gives you the possibility to adjust the amount of pressure applied on the hood seal in a second. Extremely strong design eliminating failure of the latch and danger of losing hood and the ability of sinking the ski. Available in Red, Black, Blue, Green.

The Impros Hooker 144mm impeller for the Yamaha is a 3-blade large hub diameter, radial edge design stainless steel impeller designed and intended for Bottom end and “Hook up” for Freestyle and Freeriders on a SuperJet, Blaster, or similar ski that utilizes the 144mm pump and want maximum AIR for tricks.

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

This is a similar grate to the WR201 however it is less aggressive and gives 1-2 MPH higher top speed but does not have the same braking effect as the WR201. If you want top speed and usually ride in calmer/smoother water this is the one for you. Perfectly matched to enable easy installation. Fits all years 1990-2017 Yamaha Superjet and WaveBlaster 1, 2.

Part Number: WR205

Replacement Hardware Install Kit for Blowsion Tubbie Destroyer Sponsons.

Part Number: 02-01-021

Blowsion Steering Arm Short. Compatible with all Blowsion Steering Systems and Turnplate.

Engine Block Off Plates 62T. A great way to block off access to your internal motor and all its complex innards. No more red rags or cheesy paper towels to suck through your initial engine fire off and carpet the cases with! Cool way for storing and displaying motors. Carbon Black Anodized and includes all mounting hardware. Fits all years 62T 701cc Yamaha two cylinder motors.

Part Number: 01-03-813

Heavy Duty Replacement Hood Seal. Fits all years Yamaha Super Jet, Yamaha FX-1, all years Polaris Octane, Yamaha Wave Blaster and most aftermarket hulls. Dimensions: L 2.7m x W 16mm x H 19mm.

Part Number: 04-04-411

Dual Layer 2-Tone Sheets of 1/4" (6mm) Hydro-Turf with Cut Waffle Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.

The RRP Ninja Full Carbon Competition Chin Pad Design utilizes a 3-bolt mounting system to avoid any steering system issues. This chin pad requires an RRP Steering Stop based on the rear mounting location. Thinner more streamlined design shape! Fits all RRP Cast, RRP Billet, RRP Lightweight Billet and RRP CBX Pole Models. Available in all color options listed.

DASA Flat Top Pistons now available by Blowsion. Sold Each.