Products
-
Handlebar Clamp Screw Set
Stainless steel handle bar clamp screws (4 pack). Fits Blowsion Billet Handle Bar Clamps.
Part Number: 03-05-031
Learn More -
Blowsion Pole Bracket Plate
Blowsion Pole Bracket Plate. Required when installing a Blowsion Billet Handlepole on an older (PRE-2014 DESIGN) Blowsion Dual Hole Handle Pole Bracket. Fits 1996-2020 Yamaha Superjet, 1994-1995 Yamaha FX1, 2002-2004 Polaris Octane, and Kawasaki 750 Models.
Part Number: 03-04-067
Learn More -
ADR Stroker Crankshaft - Yamaha +10mm
ADR Yamaha +10mm (78mm) Stroker Crankshaft with 133mm ADR Rods. ADR performance crankshafts are made from a super strong SCM415 crankshaft steel and go through a strict heat treatment process to control strength and reduce stress. ADR Crankshafts are available for the Yamaha Superjet in +10mm and +16mm stroker options.
Part Number: 01-03-700
Learn More -
Mikuni Low Speed Washer
Genuine Mikuni Replacement Low Speed Aluminum Washer for Mikuni SBN Carburetors. Diagram #27.
Part Number: BN38/172
Learn More -
Mikuni Pop-Off Springs
Mikuni Pop-Off Springs. Available in all sizes. Sold Each. Learn More -
Mikuni Throttle Shaft Rebuild 38MM
Genuine Mikuni replacement throttle valve rebuild kit for Mikuni Super BN 38mm Carburetors. MK-BN/038-TV.
Part Number: 01-02-536
Learn More -
OEM Yamaha Superjet Fuel Tank
Brand New OEM Yamaha Superjet Fuel Tank. Also fits most aftermarket hull applications using Yamaha based platform (Rickter, Krash, Tigercraft, ETC).
OEM Part Number: EW2-67711-01-00
Learn More -
Leak Down Block Off Kit Yamaha (62T)
Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.
Part Number: 01-03-816
Learn More -
PowerFactor Waterbox
The PowerBox was designed to be used with the PowerFactor Exhaust System.Part Number: 01-01-454
Learn More -
Base Gasket - Yamaha 650/701/760
Fits all OEM Yamaha 650, 701 and 760 Models. OEM thickness (0.020"). Replaces OEM Yamaha Base Gasket Part Numbers: 6M6-11351-A1-00, 6M6-11351-A2-00
Part Number: 01-03-323
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
RRP Ninja Chin Pad - White Base
RRP Ninja Chin Pad. Options Available with White Base. Thinner more streamlined design shape! Fits all RRP Cast, RRP Billet, RRP Lightweight Billet and RRP CBX Pole Models. Available in all color options listed.
Learn More -
Bilge Switch - Start Stop Switch Mount - Yamaha
Blowsion Bilge Switch Stop / Start Switch Mount - Yamaha. This sano billet switch assembly mounts directly to the bottom of the OEM Start / Stop switch housing of all Yamaha watercraft.
Part Number: 06-01-214
Learn More -
Blowsion Superjet Heavy Duty Steering Cable
The Blowsion Yamaha Superjet Heavy Duty Steering Cable incorporates Blue Max control cable construction. This superior control cable material is born of marine and aviation engineering design, with extreme low friction and minimal loss of motion. Fits all 1996-2007 Yamaha Superjet and most aftermarket hull applications using Yamaha based platform (Rickter, Krash, Tigercraft, ETC). Now available in 3 lengths options for shorter aftermarket hulls.
Learn More -
Handlebar Extensions
Blowsion Handlebar Extensions. Add up to an additional 2 inches to your bars. Trim lines available for custom length options.
Part Number: 03-05-139
Learn More