Products
-
ODI TLD Grips Black (130mm)
ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.
Part Number: 03-05-324
Learn More -
Blowsion Head O-Ring Kit
Our bulletproof nitrile o-ring kits come with the same quality and durability you have come to know and expect from Blowsion.
Part Number: 01-03-231
Learn More -
Flow Control Valve - Pro Series
Flow Control Valve - 3/8" Adjustable Pro Model. This 3/8" valve has been designed to prevent water flow to the waterbox at idle and off idle engine speeds. This allows the craft to be more responsive off the line and around turns. Results are HUGE gains in throttle response. All stainless internal parts. IJSBA race legal. Now Available in all Colors!
Learn More -
Pump Cone - Yamaha Superjet
Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Yamaha Superjet.
Part Number: 02-02-406
Learn More -
ODI Vans Grips Black (130mm)
So-Cal originals have teamed up to create a modern day classic waffle grip design. Check out the new Vans® Lock-On Grips by ODI.
Part Number: 03-05-361
Learn More -
DAKINE Footstrap Hardware Kit - w/glue
Now available! Dakine hardware install kit with glue for installing footstraps. Ultra sanitary and leak proof.
Part Number: 04-02-339
Learn More -
Undermatting Foam - 9mm Plush
48" x 17.5" section of 9mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.
Part Number: 04-02-328
Learn More -
Seat Cover - Yamaha WaveBlaster - Mod
Yamaha WaveBlaster MOD Seat Cover. Custom hand stitched in any combination of colors and patterns you desire.
Part Number: 04-05-002
Learn More -
Blowsion Kustom Cut-Back Stainless Impellers
Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.
Learn More -
Blowsion Pump Shoe - Yamaha 144MM
Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.
Part Number: 02-02-432
Learn More -
Water Bypass Fitting 90-Degree
Blowsion Billet 90-Degree Water Bypass fittings. Fits 3/8" ID Cooling Hoses. Offered in Anodized Clear, Black, Green, Red, Blue and Orange. All Colors In stock!
Learn More -
Primer Kit - Mikuni Dual
Fits 6mm choke shaft Mikuni dual carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and bulletproof plunger.
Part Number: 01-02-402
Learn More -
Rotary Bilge Switch - 3 Position
Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.
Part Number: 06-01-201
Learn More -
ODI Xtreme Grips Grey (130mm)
Xtreme Grips from ODI. New Graphite Grey Grip design. Starter kits come with Carbon Silver ODI Lock On Clamps and ODI’s new Snap Cap end caps. These grips feature a tapered knurl pattern that is larger and deeper where you need more traction.
Part Number: 03-05-301
Learn More -
Carburetor Adapter - Mikuni 44mm
Billet carb adaptors in stock and available to fit all Mikuni 44mm SBN Single Carb and aftermarket 44mm carb setups. Required for adapting to aftermarket air filters / flame arrestors. Flange Outer Diameter: 2.75 (inches).
Part Number: 01-02-073
Learn More