Products
-
Bilge Fitting Pro
Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.
Learn More -
Blowsion Steering System without Turnplate
Blowsion Billet aluminum steering system without turnplate. Stainless Steel Turnplate shaft rides in two O-ring sealed bearings. Included special machined Blowsion Krok Kollar stainless lock nut with set screw. Fits all stock or aftermarket Yamaha design handle poles. Steering Cap and bearing housing are carbon anodized black for corrosion protection. Works with Blowsion Kawasaki and Yamaha billet shortened turnplate. Includes 7/8" Handlebar Clamps.
Part Number: 03-05-001
Learn More -
Epoxy Resin (2 Parts Pint each) - Quart Kit
Epoxy (2 Part) - Pint Kits. High performance, gap filling, waterproof, 2 part epoxy designed to provide superior results in footwell installations, hull reinforcement and repair. Easy 1 to 1 mixing ratio keeps it simple for even the beginner.
Part Number: 06-03-122
Learn More -
Blowsion 8mm Billet Conical Washers
Blowsion 8mm Billet Conical Washers. Replace the brittle and breakable plastic nylon washers that are included with Rickter and many aftermarket hulls. Available in all Colors!
Learn More -
Destroyer Sponsons - Rickter - White
Built and shaped specific to the unique hull shape of the Rickter Freeride models (FR2, FS-2, EDGE, and EVO models) the Tubbie Destroyer is fully removable with an average 10 minute per side install and removal once hull inserts are installed. Color: White
Part Number: 02-01-008
Learn More -
Destroyer Hardware Kit
Replacement Hardware Install Kit for Blowsion Tubbie Destroyer Sponsons.
Part Number: 02-01-021
Learn More -
Blowsion Case Cranker
Blowsion Billet Crankcase Reinforcement for Yamaha Stroker crankshafts.
Part Number: 01-03-820
Learn More -
Engine Flush Kit - Single Outlet
All metal and stainless construction. Easy to use. Just push in to your 45 degree or 90 degree aftermarket aluminum water bypass(es). Backflush away!
Part Number: 06-04-001
Learn More -
T Fitting 3/8" Barbed - Black
T Hose Fitting 3/8" x 3/8" x 3/8" Barbed. Useful for different types of water routing applications. Color: Black
Part Number: 01-01-069
Learn More -
Blowsion Colored Hose - 3/8 inch
Finish the look of your engine compartment with Blowsion specialty colored 3/8" water cooling hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.
Learn More -
1/4" Quick Disconnect / Fuel Restrictor
The 1/4" Quick Disconnect / Fuel Restrictor can be used as fuel line quick disconnect and/or for fuel restriction. Pre-tapped and threaded to accept Mikuni Main Jet (Jets not included). Includes stainless steel hose clamps. Now Available in all colors!
Learn More -
Blowsion Flywheel Cover Replacement O-Ring
Replacement O-Ring Gasket Seal for all versions of the Blowsion Billet Flywheel Cover.
Part Number: 01-03-359
Learn More -
Engine Block Off Plates Yamaha (62T)
Engine Block Off Plates 62T. A great way to block off access to your internal motor and all its complex innards. No more red rags or cheesy paper towels to suck through your initial engine fire off and carpet the cases with! Cool way for storing and displaying motors. Carbon Black Anodized and includes all mounting hardware. Fits all years 62T 701cc Yamaha two cylinder motors.
Part Number: 01-03-813
Learn More -
Blowsion Handlebar Clamps
Blowsion Billet aluminum handle bar clamps for 7/8" Inch bars. Sold as a pair (2) with stainless bar clamp screws included. These bar clamps provide the finishing touch to a clean steering system. Now available in all anodized colors!
Learn More