Products
-
Primer Bulb Kit - Mikuni Single
Fits 6mm choke shaft Mikuni single carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.
Part Number: 01-02-405
Learn More -
Blowsion Handlepole Extrusion
Blowsion Billet Aluminum Handlepole Center Extrusion. Fits the Blowsion Billet Handlepole. Available in 26 inch or 29 inch Lengths.
Learn More -
Ballistic Battery Foam Spacer
Properly install and secure your ballistic battery with this foam spacer. Available for all size batteries.
Part Number: 01-04-627
Learn More -
Handle Pole Limiting Rope
The design of the Blowsion pole limiting rope is to STOP your pole from extending approx 2-3" from total max extension. This prevents the forward motion of the pole and riders body from destroying expensive handlepoles, pole brackets, hulls and also expensive human body parts!
Part Number: 03-04-151
Learn More -
Handlebar Clamp Screw Set
Stainless steel handle bar clamp screws (4 pack). Fits Blowsion Billet Handle Bar Clamps.
Part Number: 03-05-031
Learn More -
Blowsion Cylinder Head Dome
Each dome includes a dome locking system that prevents it from spinning when servicing spark plugs. One dome per package.
Learn More -
Blowsion Corporate Sticker 17"
Blowsion Corporate Sticker 17 inch. 12 color combos to choose from. These are not cheezy vinyl. Full screen-printed die cuts with UV protective clear. Show your vanity! Sold Each.
Learn More -
Bilge Switch Replacement - 9ft Wire
Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.
Part Number: 06-01-215
Learn More -
Blowsion Krok Kollar
Blowsion Stainless Steel machined Steering Lock nut. Includes stainless binding screw. Prevents standard lock nut torque failure. Not something made in the land of won-tons or available at your local hardware store!
Part Number: 03-05-019
Learn More -
Installation Materials Kit - Footwells / Hull Reinforcement
Each kit includes all materials needed for mixing into, and handling, your installation resin (available separately). Silica Thickener, Mixing Cups, Brushes, Gloves and Knitted fabric cloth for all seams.
Part Number: 06-03-113
Learn More -
Super Base Gasket - Yamaha
This is an OEM Yamaha thickness (0.020") super cylinder base gasket. Teflon coated with metal core for blow-out protection. Fits all OEM Yamaha 650, 701 and 760 Models.
Part Number: 01-03-321
Learn More -
Mikuni Super BN Carb Bolt Kit
Blowsion Stainless Steel Socket Head Bolt Kit for Mikuni Super BN Carburetors. The Socket Head Bolt design allows for use of hex key tool which results in much easier access. Replace those easy to strip Mikuni phillips head screws before it is too late!
Part Number: 01-02-547
Learn More -
Blowsion Cylinder Sleeve - Yamaha 850
Yamaha SuperJet 850 Big Bore Sleeves. Fits 89mm to 91mm Piston. Performance Pre-Ported. To be used with stock stroke through 6 mil stroker motors. Blowsion custom designed include a wider exhaust port, wider boost port, deeper transfers and a narrowed skirt.
Part Number: 01-03-452
Learn More -
Blowsion Steering System Rebuild Kit
Blowsion Steering System Rebuild kit includes roller bearing, thrust washers, thrust bearing, and large and small O-rings.
Part Number: 03-05-020
Learn More -
Blowsion Mat Glue - Quart
Blowsion Mat Kit Glue "Blow Goo" to the rescue. Use this solvent-based contact adhesive with your Hydro Turf or stitched mat kit and never worry again about your mats coming loose. Not water-based!
Part Number: 06-03-142
Learn More -
Chin Pad Cover - Glove-Fit - 96+ Superjet / FX1 / Octane
Blowsion custom stitched glove-fit chin pad covers for 1996+ Yamaha Superjets, FX1 and Polaris Octane. Specifically designed to fit our Blowsion Carbon Chin Pads but will also fit OEM Yamaha chin pad backing with slight modification to OEM plastic backing and foam padding.
Part Number: 04-01-901
Learn More