Products
-
Blowsion Barcade Tank Top
Blowsion Barcade Tank Top. Unisex Sizing. Available in all sizes. Color: Black.
Learn More -
Fuel Tank Check Valve 1/4"
Allows air to flow in one direction. 1/4" Barbed ends. Available in clear/black only.
Part Number: 01-02-554
Learn More -
Blowsion Snapback Since89 Hat - Black/Green
Blowsion Snapback Since89 Hat. 5 Panel black with mesh back and rounded visor. 58cm. Color: Black/White
Part Number: 07-02-558
Learn More -
Destroyer Hardware Kit
Replacement Hardware Install Kit for Blowsion Tubbie Destroyer Sponsons.
Part Number: 02-01-021
Learn More -
Pump Cone - Kawasaki
Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Kawasaki SXR, 750SX, SXI, SXi-Pro, X2 and 650SX Models.
Part Number: 02-02-405
Learn More -
Bilge Pump Mount - Kawasaki 550/650/750SX
The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-106
Learn More -
Blowsion SS Jet Ski Cover - Kawasaki 750SX
Blowsion Stealth Series PWC Jet Ski Covers. No more cover flapping on the freeway. Weather resistant material with special UV coating. Engineered for a custom fit for each PWC model. Fits all 1992-2002 Kawasaki 750SX, 750SXI and 750SXi-Pro Models. Color: Stealth Black.
Part Number: 06-06-037
Learn More -
Blowsion Hood Seal
Heavy Duty Replacement Hood Seal. Fits all years Yamaha Super Jet, Yamaha FX-1, all years Polaris Octane, Yamaha Wave Blaster and most aftermarket hulls. Dimensions: L 2.7m x W 16mm x H 19mm.
Part Number: 04-04-411
Learn More -
Bilge Pump Dual Mount - Kawasaki
Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-101
Learn More -
Mat Kit - Diggers - Yamaha FX1
Blowsion Custom Cut Mat Kit. Glue it On! Fits all 1994-1995 Yamaha FX-1 Models with Digger Footwells. Includes bottom, tray sides, dash, footwell mat pieces, and undermat foam. Digger Footwells not included. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.
Part Number: 04-02-053
Learn More -
Mat Kit - Stitched - Digger Footwells - Yamaha Superjet (1990-1995)
Glue On! Includes bottom, sides, dash and undermat foam. Fits all years 1990-1995 Yamaha Superjet Models with Digger Composite Footwells. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.
Part Number: 04-02-069
Learn More -
Blowsion Rickter Edge Neon Green 701cc
This brand spankin new Rickter Edge FR has all the show and go to make a complete freeride weapon. Complete new build from the ground up with an OEM Yamaha 701 at the heart of it. Propelling the ski to launch and slash waves is a Billet 148mm Skat-Trak Magnum Set-Back pump. For rideability and reliability it has an OEM ignition system along with Factory Pipe Limited setup with VK Carbon Exhaust Chamber. Controls are all Blowsion, and the center of it is our Billet Lightweight Handlepole. This ski has just been put on display in the Blowsion showroom and is available to ship immediately!
Part Number: 10-01-064
Learn More -
Battery Box Strap - Heavy Duty
Blowsion Heavy Duty Freeride Battery Strap. Much Stronger and slightly shorter than OEM Yamaha straps which takes away the slack when using aftermarket batteries. 10 inches total length (hook to hook).
Part Number: 01-04-604
Learn More -
Blowsion Steering System Rebuild Kit
Blowsion Steering System Rebuild kit includes roller bearing, thrust washers, thrust bearing, and large and small O-rings.
Part Number: 03-05-020
Learn More -
Blowsion Boxed T-Shirt Teal
Blowsion Corporate Boxed Logo Short Sleeve T-Shirt. Unisex Sizing. Available in all sizes. Color: Teal with Black Logo.
Learn More -
Blowsion Turbulator Chin Pad
New Blowsion Turbulator Chin Pad. Specifically designed and form fit for the Blowsion Billet Handlepole. Custom Color options available!
Learn More