Products

Inline Water Filter. Made from impact resistant nylon with 3/8” barb ends. A clear bowl and removable filter screen allow easy inspection and cleaning.

Part Number: 01-01-780

These hand-laid, molded fiberglass insets provide extended room in the tray of your ski to position your feet. Comfortably sized for average feet (sizes 6-11), these footwells also feature a gentle protrusion over the top of your foot.

Part Number: 05-03-004

Blowsion FlexFit One Ten Snapback Hat. Color: Black with Purple Logo.

Part Number: 07-02-433

316 Stainless Steel Heavy Duty T-Bolt Hose Clamp for 3.5" Exhaust Couplers. Compatible with all TNT, RRP Carbon and PowerFactor Style Exhaust Systems.

Part Number: 01-01-175

Mikuni Diaphragm Mount throttle cable bracket. Trick mounting setups are enabled with this handy bracket. Stainless Steel Mounting Hardware Included. Now available in two sizes.

Blowsion Classic Snapback Hat. One Size Fits Most. Color: Black/Charcoal.

Part Number: 07-01-841

Blowsion 8mm Billet Conical Washers. Replace the brittle and breakable plastic nylon washers that are included with Rickter and many aftermarket hulls. Available in all Colors!

Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.

Part Number: 01-03-816

Fits 8mm choke shaft Keihin single carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-407

Made out of injection molded flexible urethane. Attaches to your watercraft with its own adhesive backing. Each kit includes special pre-wipe cleaner to promote maximum adhesion and durability. The 5/8" size is perfect for all years Kawasaki JS 440/550, Kawasaki 750SXi and Yamaha FX1.

Part Number: 04-02-304

Blowsion stainless Steering Stop and nut. Updated design allows for two mounting positions for riders wanting more steering throw. Fits all OEM, UMI,Factory Yamaha, RRP and AC aluminum Handlepoles.

Part Number: 03-04-131

Blowsion Custom Cut Mat Kit. Glue it On! Fits all Kawasaki 750SX, SXi and SXi-Pro Models with Kicker Footwells. Includes bottom, tray sides, dash, footwell mat pieces, and undermat foam. Kicker Footwells not included. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.

Part Number: 04-02-004

Blowsion Billet Carburetor Fuel Rail. Fits all Mikuni SBN 44mm, 46mm Dual Carburetors. All Stainless Mounting hardware included. Available in all Anodized colors!

Blowsion Billet 6061 aluminum replacement for the cast factory OEM bracket on all 1995 and older Yamaha Super Jets. Oversize length of breather tubing included. Includes oversize cable routing hole for installing the handlepole breather tubing. Blowsion design also includes handlepole spring mounting hole for riders that desire a light pole set up. Totally sanitary and necessary upgrade from the feeble cast aluminum OEM bracket.

Part Number: 03-03-002

Blowsion Crime Short Sleeve T-Shirt. Unisex Sizing. Available in all sizes. Color: Black Heather.