Products
-
Leak Down Block Off Kit Yamaha (62T)
Blowsion Engine Leak Down Block Off Kit. This is an essential tool for determining engine health. Make sure your fresh rebuilt engine is sealed properly, or use it to diagnose engine and/or tuning issues. Utilize your existing leak down tester or plug your Pop-off pressure gauge into the pulse fitting on your cases and check for air leaks. Includes anodized aluminum plates and rubber gaskets to match. All mounting hardware included. Fits all years 62T 701 engines and 62t 760 engines with a b-pipe manifold.
Part Number: 01-03-816
Learn More -
Gauge Block Off - WaveBlaster
Get rid of that unsightly gauge window on the side of your Blaster with this sano billet piece. Installs with the OEM mounting hardware. Fits all years Yamaha WaveBlaster.
Part Number: 05-04-450
Learn More -
OEM Yamaha Starter Motor
Genuine OEM Yamaha Starter Motor. Fits all Yamaha SuperJet, FX1 and WaveBlaster.
OEM Part Number: 6M6-81800-10-00
Learn More -
Floating Lanyard Multi End
Multi Fit Floating Lanyard - Works on all models of PWC except Sea Doo with DESS.
Part Number: 07-04-550
Learn More -
GET C1 Hour Meter
The GET C1 Engine Hour Meter keeps track of your engine's service life. The meter fits to any bike in minutes without any wiring needed and detects the engine by identifying wave frequencies that flow through the surface it sits on.
Part Number: 06-04-092
Learn More -
Throttle Adapter - Yamaha (6mm)
6mm Throttle Cable Adapter. A Throttle Cable Adapter is required to run most aftermarket throttle levers. Fits All Years Yamaha Two Stroke and 2021+ Yamaha Superjet PWC Models. Please see list below for model compatibility.
Part Number: 03-05-242
Learn More -
Primer Bulb Kit - Mikuni Single
Fits 6mm choke shaft Mikuni single carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.
Part Number: 01-02-405
Learn More -
OEM Yamaha Impeller Housing 144MM
OEM Yamaha 144mm Pump Impeller Housing. Fits all years Yamaha Superjet, WaveBlaster 1 and Rickter Hull Models.
Part Number: 6R7-51312-03-94 / 6R7-51312-03-00
Learn More -
ADA Exhaust Bracket - Yamaha 701
ADA Racing Yamaha 701 Cylinder Head Exhaust Bracket for Non-girdled ADA cylinder heads. This bracket only works with the 3 bolt 701 Superjet style exhaust. It does NOT work with the 4 bolt 760 exhaust. Includes mounting bolts and spacers.
Part Number: YEXBRKT-2L
Learn More -
Blowsion Cylinder Sleeve - Yamaha 785
Yamaha 785 SuperJet 84-86.5mm Big Bore Sleeves. Performance Pre-Ported. To be used with stock stroke through 6 mil stroker motors. Blowsion custom designed include a wider exhaust port, wider boost port, deeper transfers and a narrowed skirt. Sold Each.
Part Number: 01-03-451
Learn More -
Exhaust Manifold Gasket - Yamaha 701 (61X)
Yamaha 701 61X Exhaust manifold Gasket. Fits 1994-2017 Yamaha 701 Superjet, 1994-1995 Yamaha FX1, and 1993-1996 Yamaha WaveBlaster 701 Models.
Part Number: 01-01-734
Learn More -
Mikuni Arm Pin Screw
Genuine Mikuni Replacement Mikuni Arm Pin Screw for Mikuni SBN Carburetors. Diagram #41.
Part Number: C6-0308-G
Learn More -
DASA Cylinder Base Gasket
DASA Replacement Cylinder Base Gasket. Available for 85mm and 89-94mm Billet Cylinder Kits.
Learn More -
OEM Starter Bendix - Yamaha / Kawasaki
OEM Kawasaki Starter Bendix. Fits All Kawasaki and Yamaha Models.
Part Number: 13101-3708 Learn More
-
Yamaha Fuel Cap Gasket
Aftermarket Yamaha Fuel Cap Gasket. Fits All Yamaha Models PWC. Fits OEM Yamaha and Blowsion Yamaha Billet Fuel Caps. Replaces OEM Yamaha PN# EU0-67832-00-00.
Part Number: 01-07-231
Learn More -
ODI Blowsion Lock Ring End Caps
ODI Grip Blowsion Logo Lock Ring End Cap Combo- now you can have the anodized bling look all the way through to the end cap. Each kit includes inner lock rings, and outer lock ring/caps w/ hardware.
Learn More