Pump & Handling
-
Blowsion Kustom Cut-Back Stainless Impellers
Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.
Learn More -
Blowsion Pump Shoe - Yamaha 144MM
Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.
Part Number: 02-02-432
Learn More -
Blowsion Pump Shoe - Yamaha 148MM
The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.
Part Number: 02-02-434
Learn More -
Jet Dynamics Intake Grate - Octane
The best scoop grate on the market for clawing the maximum amount of water into the thirsty Polaris Octane Pump. The Jet Dynamics Top loader design is unbeatable for all around performance.
Part Number: 02-01-198
Learn More -
Jet Dynamics Intake Grate - Superjet 2008+
The best scoop grate on the market for clawing the maximum amount of water into the thirsty 2008+ Super Jet pump. The Jet Dynamics Top loader design is unbeatable for all around performance.
Part Number: 02-01-154
Learn More -
Jet Dynamics Ride Plate - Octane - Extended Length
JET DYNAMICS Use this ride plate in conjunction with the Jet Dynamics Polaris Octane intake grate and you finally have a handling set up that keeps that Octane under control.
Part Number: 02-01-281
Learn More -
Pump Cone - Polaris / Magnum Pumps
The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.
Part Number: 02-02-407
Learn More -
RRP Tilt Kit - Yamaha 144MM
The RRP Yamaha Freestyle Trim System for Yamaha 144mm & 148mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.
Part Number: 02-02-510
Learn More -
RRP Trim Ring
RRP Trim Ring Only. Fits RRP 144MM and 155MM Freestyle Tilt Kits. Available in Black, Silver, Red and Blue/p> Learn More
-
Skat-Trak Trim Cable Long (Yamaha Pulley System)
Skat-Trak Trim Cable Long for Yamaha Pulley Systems. Fits all Blowsion trim and tilt systems with pulley system. Direct replacement for Skat-Trak and Blowsion systems.
Part Number: 02-02-544
Learn More -
Solas Yamaha Magnum Pump 144MM
SOLAS Yamaha 12 Vane 144mm Stainless Magnum Pump. Fits all years Yamaha Superjet and WaveBlaster with standard length driveshaft. Pump Bearings and Seals Not Included.
Part Number: 02-02-020
Learn More -
Tubbie I and II Sponsons - Universal Fit -Screw On
Don't sell that SXI Pro, Yamaha Superjet or Octane to buy an SXR or Hydrospace to be competitive in racing or against your buddies on the waves or lake. The Tubbies are the equalizer.
Learn More -
WORX Ride Plate - WR309 - Polaris Octane
The best all-around Octane ride plate available! With the WORX 309 you can gain greater craft stability and control, and save valuable energy. "D" cutout helps stick your craft in rough water conditions and while turning. The most commonly used ride plate.
Part Number: WR309
Learn More