Bilge Accessories
-
Vacate Valve - Kawasaki
A simple installation drain valve alternative for the OEM drain plugs in Kawasaki model Watercraft. Available in Black, Clear and Green. Sold Each.
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
OEM Bullet Terminals - 20 Pack
Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.
Part Number: 01-04-418
Learn More -
Expanding Foam (2 Part) - Quart Kit
No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.
Part Number: 06-03-132
Learn More -
Expanding Foam (2 Part) - Pint Kit
No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.
Part Number: 06-03-131
Learn More -
Duckbill One Way - Replacement
Replaces your worn out rubber duckbill. Includes color-matched Zip Tie.
Part Number: 06-01-010
Learn More -
Duckbill One Way - Kawasaki
Billet SXR Duckbill- eliminates water via the OEM Kawi SXR drain plug orifice at the rear of the ski. This is the most economical way to keep the SXR engine compartment dry. Not a cheap universal mount, this drain bladder is billet and designed specifically for the Kawasaki SXR 800.
Part Number: 06-01-015
Learn More -
CAS Billet Aluminum Flange Only
Available for riders wanting to use the end flange only for custom scupper and rear exhaust installations etc. The new billet flange assembly is the premium design setup and allows use of the Blowsion billet exhaust outlet so vain riders can sanitize both sides of the rear of their watercraft. Fits all years Super Jet, KAWI 750 and SXR 800, KAWI 650, and Polaris Octane. Anodized Clear.
Part Number: 06-01-023
Learn More -
Bilge Switch / Primer Mounting Plate
This cool universal anodized black aluminum mounting plate allows easy mounting of the rotary bilge switch as well as primer bulb on the dash. Specifically designed for the SXR but will work with other models. Inside mounting with the correct bulb style primer hole and rotary bilge switch ID means a sanitary install in minutes with no grinders or tubes of silicone needed.
Part Number: 04-06-002
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
Bilge Pump Hose - 10FT
Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-302
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More