Intake
-
Primer Bulb Kit - Mikuni Dual
Fits 6mm choke shaft Mikuni dual carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.
Part Number: 01-02-406
Learn More -
Primer Bulb Kit - Mikuni Single
Fits 6mm choke shaft Mikuni single carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.
Part Number: 01-02-405
Learn More -
DASA Intake Manifold O-Ring Kit
DASA Intake Manifold O-Ring Rebuild Kit. Includes replacement O-Rings for V Force 2 Reeds and Carburetor Speed Plate.
Part Number: 01-02-248
Learn More -
Blowsion Colored Hose Kit
Finish the look of your engine compartment with a Blowsion Colored Hose Kit. Hose Kit includes 10 foot lengths of 1/8 Primer, 1/4 Fuel and 3/8 Water lines. Available in Black, Blue, Green, Orange, Red, or Yellow.
Learn More -
Billet Carburetor Block Off
Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.
Part Number: 01-02-557
Learn More -
Blowsion Tornado Filter 1.5
Blowsion Tornado Filter (1.5 inches tall). Even Shorter Version Now Available! For those who require a little shorter flame arrestor for hood clearance. 4 x 1.5" Inches Tall. Available in Anozided Black, Clear, Blue, Green, Orange, Red and Purple. Sold Each.
Learn More -
Throttle Cable Bracket - Diaphragm Mount
Mikuni Diaphragm Mount throttle cable bracket. Trick mounting setups are enabled with this handy bracket. Stainless Steel Mounting Hardware Included. Now available in two sizes.
Learn More -
Fuel Filter - Water Separator
The preferred choice for fuel filters and water separators. Fits all Yamaha Standups. Can be used also with KAWI and Polaris Octane models. 1/4" Inlet/Oulet hose size.
Part Number: 01-02-551
Learn More -
Fuel Tank Check Valve 1/4"
Allows air to flow in one direction. 1/4" Barbed ends. Available in clear/black only.
Part Number: 01-02-554
Learn More -
Mikuni 44MM Dual Carburetor Kit
Dual Mikuni 44mm SBN Carburetor Kit. Linked and Custom Jetted to your engine specification. Available in 5 color options!
Learn More -
1/4" Quick Disconnect / Fuel Restrictor
The 1/4" Quick Disconnect / Fuel Restrictor can be used as fuel line quick disconnect and/or for fuel restriction. Pre-tapped and threaded to accept Mikuni Main Jet (Jets not included). Includes stainless steel hose clamps. Now Available in all colors!
Learn More -
Blowsion Fuel Tank
The Blowsion Fuel Tank is specially designed to work in conjunction with the aftermarket lay down style exhaust systems that don't work with the OEM Yamaha Fuel Tank (RRP, TNT, PowerFactor). One of the main problems with using these exhaust systems is the battery has to be relocated which can cause quite the problem. The Blowsion Fuel Tank is unique as it has a cut out in the front of the tank that enables you to relocate your battery with ease. Fuel Capacity: 4 Gallons.
Learn More -
Pulse Line Fitting 1/4"
Brass Press In Straight Pulse Line Nipple Fitting 1/4" Hose Barb. Use for dual carburetor setups with dual fuel pumps where a second pulse line is required.
Part Number: 01-02-530
Learn More -
Blowsion Fuel Tank Fitting
Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.
Part Number: 01-02-598
Learn More -
Mikuni 46MM Dual Carburetor Kit
Dual Mikuni 46mm SBN Carburetor Kit. Linked and Custom Jetted to your engine specification. Available in 5 color options!
Learn More -
Blowsion Outerwears
Blowsion logo Outerwears flame arrestor water-resistant screens. Specifically formulated to prevent water ingress. Available for tapered tornado filters. Sold Each.
Learn More