Fuel Supply Systems
-
1/4" Quick Disconnect / Fuel Restrictor
The 1/4" Quick Disconnect / Fuel Restrictor can be used as fuel line quick disconnect and/or for fuel restriction. Pre-tapped and threaded to accept Mikuni Main Jet (Jets not included). Includes stainless steel hose clamps. Now Available in all colors!
Learn More -
1/4" Quick Disconnect with Shut-Off Valve
Motion Pro Fuel Shut-Off Valve 1/4" Separating Quick Connect (MP#12-0029).
Learn More -
Blowsion Billet Fuel Cap - Yamaha
Blowsion Low Pro Billet aluminum fuel caps for all Yamaha watercraft. Low profile smooth design allows for outside fueling, yet will not get in the way during aerial or freestyle moves around the front of the watercraft. Available in all anodized colors!
Learn More -
Blowsion Colored Hose - 1/4 inch
Finish the look of your engine compartment with Blowsion specialty colored 1/4" fuel hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.
Learn More -
Blowsion Colored Hose - 1/8 inch
Finish the look of your engine compartment with Blowsion specialty colored 1/8" fuel primer hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot.
Learn More -
Blowsion Colored Hose Kit
Finish the look of your engine compartment with a Blowsion Colored Hose Kit. Hose Kit includes 10 foot lengths of 1/8 Primer, 1/4 Fuel and 3/8 Water lines. Available in Black, Blue, Green, Orange, Red, or Yellow.
Learn More -
Blowsion Fuel Tank
The Blowsion Fuel Tank is specially designed to work in conjunction with the aftermarket lay down style exhaust systems that don't work with the OEM Yamaha Fuel Tank (RRP, TNT, PowerFactor). One of the main problems with using these exhaust systems is the battery has to be relocated which can cause quite the problem. The Blowsion Fuel Tank is unique as it has a cut out in the front of the tank that enables you to relocate your battery with ease. Fuel Capacity: 4 Gallons.
Learn More -
Blowsion Fuel Tank Fitting
Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.
Part Number: 01-02-598
Learn More -
Fuel Filter - Water Separator
The preferred choice for fuel filters and water separators. Fits all Yamaha Standups. Can be used also with KAWI and Polaris Octane models. 1/4" Inlet/Oulet hose size.
Part Number: 01-02-551
Learn More -
Fuel Pickup Filter 1/4"
Universal Fuel Pickup Filter. Add some of these for extra fuel filtration and also keeps the fuel in your lines when going upside down.
Part Number: 01-02-449
Learn More -
Fuel Tank Check Valve 1/4"
Allows air to flow in one direction. 1/4" Barbed ends. Available in clear/black only.
Part Number: 01-02-554
Learn More -
Inline Fuel Filter 1/4"
Inline Fuel Filter 1/4". Clear Plastic for High Volume, Low pressure Fuel Systems. Inline fuel filters filter out those harmful particles that can cause engine damage.
Part Number: 01-02-550
Learn More -
Keihin Carb Rebuild Kit 38-44MM CDK-II
Aftermarket Keihin Carburetor Rebuild Kit for 38mm, 40mm, 42mm and 44mm CDK-II Carburetors. Fits wide range of 38-44mm Keihin™ CDK-II carbs found on PWC. Includes Viton™ tipped inlet needle.
Part Number: 01-02-492
Learn More -
Small Fuel Tank - For PF/RRP Pipe
Reduced size 8.5 Liter (2.25 Gal) fuel tank. Less weight- required when using TNT, RRP or PowerFactor Pipes. Specially designed fuel tank incorporates lower baffle section to reduce fuel sloshing guaranteeing uninterrupted fuel supply. Comes equipped with Dual Fuel Pickups, Fuel Pickup Filters and Fuel Tank Fittings for Gas Tank Vent and Return Lines.
Learn More