Composites

This is the FINAL answer for keeping your stitched and Hydro Turf mat kit edges stuck down. Use to seam edges permanently. Once dry it creates seamless perfection.

Part Number: 06-03-151

Direct water and air to where you want it in the engine compartment! Drop Tube and Urethane Flange for Hood Baffle Air Intakes. Use with either aftermarket hoods or stock factory hood to increase air flow. Each kit includes three oversize lengths of hose tubing and urethane flanges. Bond-able to hand laid fiberglass, carbon, SMC or ABS inner liners these are simple to install and are an excellent answer for air-starved motors. An EXCELLENT choice for the Kawasaki SXR 800 with the Factory Pipe installed!

Part Number: 05-02-199

Replacement RRP Rickter Adjustable Footwell Binding Bracket Plates for Yamaha Superjet. Set Includes Left and Right Side. Anodized Black.

Part Number: 05-03-026

Blowsion Carbon composite tank holder keeps the tank from sliding around in the bottom of a hull during freestyle maneuvers. Available for Small Fuel Tank and OEM/ColdFusion Yamaha Fuel Tanks.

Replacement RRP Standard Footwell Bindings Only. Includes Left and Right Side Foot hold. No Hardware or Mounting Brackets are Included.

Part Number: 05-03-024

The RRP Rickter Front Foothold is wrapped with two layers of 9mm premium plush underpad with Rickter’s durable yet soft molded diamond Hydro-Turf EVA. Also includes install hardware of 4 x M8 Countersunk bolts, Washers, Locknuts, and RRP AB Washers for a clean and strong installation. The EVA is wider on the sides of the binding to accommodate a range of tray sizes. Light trimming of the EVA Is recommended for the ideal fit followed by drilling four holes in the dash to install the binding at the desired height.

Part Number: 05-03-019

If you are looking for a bedding compound with exceptionally strong adhesion, and are not concerned about later removal of hardware, 3M Fast Cure 5200 should be at the top of your list. Along with outstanding adhesion, 3M Fast Cure 5200 remains flexible after it cures and it can be used above or below the waterline. Ideal for underwater thru-hull fittings, hull-to-deck joints, portholes and bonding wood to fiberglass.

Part Number: 06520

3M Marine Grade Silicone creates a rubbery waterproof seal that remains flexible and is mildew resistant. For sealing Lexan™, Plexiglass™, gelcoat, fiberglass, wood, glass, metal, rubber, and vinyl. Cured sealant remains flexible.

Part Number: 08029

Epoxy (2 Part) - Pint Kits. High performance, gap filling, waterproof, 2 part epoxy designed to provide superior results in footwell installations, hull reinforcement and repair. Easy 1 to 1 mixing ratio keeps it simple for even the beginner.

Part Number: 06-03-122

Epoxy (2 Part) - Quart Kits. High performance, gap filling, waterproof, 2 part epoxy designed to provide superior results in footwell installations and hull reinforcement and repair. Easy 1 to 1 mixing ratio keeps it simple for even the beginner.

Part Number: 06-03-123

No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.

Part Number: 06-03-131

No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.

Part Number: 06-03-132

These hand-laid, molded fiberglass insets provide extended room in the tray of your ski to position your feet. Comfortably sized for average feet (sizes 6-11), these footwells also feature a gentle protrusion over the top of your foot.

Part Number: 05-03-004

Blowsion Kicker Footwells were Designed specifically for the Super Jet and Kawasaki SX-R 800, and used exclusively by Ross Champion on his Factory Blowsion Yamaha SuperJets and Air Darin Anderson on his SXR's and SJ's.

Part Number: 05-03-005

The Blowsion Klowner Footwells were designed especially for the rider who need MAX room in the tray. These hand-laid, molded fiberglass insets provide extended room in the tray of your ski to position your feet. Comfortably sized for large to very large feet.

Part Number: 05-03-007