Composites
-
VK Carbon Hood Kit - Kawasaki SXR 1500
VK Carbon Fiber Hood Kit for the Kawasaki SXR 1500. Includes Drop Tubes and EVA Hood Pad.
Part Number: 05-02-127
PLEASE NOTE: This product is currently unavailable.Learn More -
VK Carbon Tri-Wave Rideplate - Kawasaki SXR 1500 (Short)
VK Composites Carbon Look Infused Epoxy Resin Tri-Wave Rideplate for 2017 and Newer Kawasaki SXR 1500 Models. Length: 15.75 inches
Part Number: 02-01-704
PLEASE NOTE: This product is currently unavailable.Learn More -
RRP Rickter Front Foothold
The RRP Rickter Front Foothold is wrapped with two layers of 9mm premium plush underpad with Rickter’s durable yet soft molded diamond Hydro-Turf EVA. Also includes install hardware of 4 x M8 Countersunk bolts, Washers, Locknuts, and RRP AB Washers for a clean and strong installation. The EVA is wider on the sides of the binding to accommodate a range of tray sizes. Light trimming of the EVA Is recommended for the ideal fit followed by drilling four holes in the dash to install the binding at the desired height.
Part Number: 05-03-019
Learn More -
3M 5200 Marine Adhesive Sealant Fast Cure White (10oz)
If you are looking for a bedding compound with exceptionally strong adhesion, and are not concerned about later removal of hardware, 3M Fast Cure 5200 should be at the top of your list. Along with outstanding adhesion, 3M Fast Cure 5200 remains flexible after it cures and it can be used above or below the waterline. Ideal for underwater thru-hull fittings, hull-to-deck joints, portholes and bonding wood to fiberglass.
Part Number: 06520
Learn More -
3M Marine Grade Silicone Sealant Clear (10oz)
3M Marine Grade Silicone creates a rubbery waterproof seal that remains flexible and is mildew resistant. For sealing Lexan™, Plexiglass™, gelcoat, fiberglass, wood, glass, metal, rubber, and vinyl. Cured sealant remains flexible.
Part Number: 08029
Learn More -
SXR Composite Rail Caps
Get rid of those extremely slippery factory rubber black rails and go composite. Available in gel coat white and ready to mount and go. Combine them with either our stitched, or Hydro Turf SXR mat kits and you are ready to rip.
Part Number: 05-04-001
Learn More -
Epoxy Resin (2 Parts Pint each) - Quart Kit
Epoxy (2 Part) - Pint Kits. High performance, gap filling, waterproof, 2 part epoxy designed to provide superior results in footwell installations, hull reinforcement and repair. Easy 1 to 1 mixing ratio keeps it simple for even the beginner.
Part Number: 06-03-122
Learn More -
Epoxy Resin (2 Parts Qt each) - 1/2 Gallon Kit
Epoxy (2 Part) - Quart Kits. High performance, gap filling, waterproof, 2 part epoxy designed to provide superior results in footwell installations and hull reinforcement and repair. Easy 1 to 1 mixing ratio keeps it simple for even the beginner.
Part Number: 06-03-123
Learn More -
Expanding Foam (2 Part) - Pint Kit
No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.
Part Number: 06-03-131
Learn More -
Expanding Foam (2 Part) - Quart Kit
No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.
Part Number: 06-03-132
Learn More -
Footwells - Dawson Digger
These hand-laid, molded fiberglass insets provide extended room in the tray of your ski to position your feet. Comfortably sized for average feet (sizes 6-11), these footwells also feature a gentle protrusion over the top of your foot.
Part Number: 05-03-004
Learn More -
Footwells - Kickers
Blowsion Kicker Footwells were Designed specifically for the Super Jet and Kawasaki SX-R 800, and used exclusively by Ross Champion on his Factory Blowsion Yamaha SuperJets and Air Darin Anderson on his SXR's and SJ's.
Part Number: 05-03-005
Learn More -
Footwells - Klowners
The Blowsion Klowner Footwells were designed especially for the rider who need MAX room in the tray. These hand-laid, molded fiberglass insets provide extended room in the tray of your ski to position your feet. Comfortably sized for large to very large feet.
Part Number: 05-03-007
Learn More -
Hull Reinforcement Kit - Carbon Fiber
Why buy a bunch of confusing fiberglass materials to reinforce your ski when we can provide you with just the right amount. Pre cut tri-axial panels to reinforce both sides of your ski.
Part Number: 05-05-012
Learn More -
Hull Reinforcement Kit - Nytex
Why buy a bunch of confusing fiberglass materials to reinforce your ski when we can provide you with just the right amount. Pre cut tri-axial panels to reinforce both sides of your ski.
Part Number: 05-05-011
Learn More -
Installation Materials Kit - Footwells / Hull Reinforcement
Each kit includes all materials needed for mixing into, and handling, your installation resin (available separately). Silica Thickener, Mixing Cups, Brushes, Gloves and Knitted fabric cloth for all seams.
Part Number: 06-03-113
Learn More