Search results for 'Sxr'
-
ODI TLD Grips Aqua (130mm)
ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.
Part Number: 03-05-329
Learn More -
ODI TLD Grips Pink (130mm)
ODI has enlisted the help of our good friends over at Troy Lee Designs to help put an artistic spin on a quality design. After hundreds of drawings and designs, what has been developed is one of the most innovative ODI grips yet...The ODI TLD Lock-On Grip.
Part Number: 03-05-330
Learn More -
ODI Vans Grips Gum (130mm)
So-Cal originals have teamed up to create a modern day classic waffle grip design. Check out the new Vans® Lock-On Grips by ODI. Grip set includes Lock-On grips, black checkered clamps, and screws.
Part Number: 03-05-364
Learn More -
Undermatting Foam - 9mm Plush
48" x 17.5" section of 9mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.
Part Number: 04-02-328
Learn More -
Undermatting Foam - 26mm Plush
48" x 17.5" section of 26mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.
Part Number: 04-02-330
Learn More -
Blowsion Tornado Filter 1.5
Blowsion Tornado Filter (1.5 inches tall). Even Shorter Version Now Available! For those who require a little shorter flame arrestor for hood clearance. 4 x 1.5" Inches Tall. Available in Anozided Black, Clear, Blue, Green, Orange, Red and Purple. Sold Each.
Learn More -
Inline Fuel Filter 1/4"
Inline Fuel Filter 1/4". Clear Plastic for High Volume, Low pressure Fuel Systems. Inline fuel filters filter out those harmful particles that can cause engine damage.
Part Number: 01-02-550
Learn More -
RRP Steering Stop / Support
Rick Roy Products billet aluminum Steering Stop / Chin pad Support. This product is required for all RRP Handlepoles when fitting an RRP Chin Pad (Kawasaki, Yamaha, Rickter, Kommander, etc.). Designed to provide additional support to chin pads and prevent them from crushing or flexing. May fit other brands of handlepoles as well. Anodized, includes stainless hardware.
Learn More -
Blowsion Colored Hose - 1/8 inch
Finish the look of your engine compartment with Blowsion specialty colored 1/8" fuel primer hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot.
Learn More -
Blowsion Colored Hose - 1/4 inch
Finish the look of your engine compartment with Blowsion specialty colored 1/4" fuel hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.
Learn More -
Blowsion Colored Hose - 3/8 inch
Finish the look of your engine compartment with Blowsion specialty colored 3/8" water cooling hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.
Learn More -
Undermatting Foam - 18mm Plush
48" x 17.5" section of 18mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.
Part Number: 04-02-331
Learn More -
ODI Cross Trainer Grips Black (130mm)
The ODI Cross Trainer 130mm Lock-On Grip Set features soft comfortable rib patterns interlaced with a thicker criss-cross pattern for a soft feel without a loss in control. Made in the USA!
Part Number: 03-05-370
Learn More -
Hydro-Turf Sheet - Dual Layer - Diamond
Dual Color Sheets of 1/4" (5.5mm) Hydro-Turf with Cut Diamond Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.
See our special formulated solvent-based Mat Glue for Installation.
Learn More -
RRP Throttle Lever
RRP Rickter Throttle Lever. Available in Black, Red, Blue or Silver.
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More