Search results for 'pump'

Thrust Innovations replacement Pump Shoe Seal for Yamaha 155mm Pumps. A Direct Replacement for the discontinued OEM Yamaha 155mm Pump Shoe Seal (OEM Yamaha PN# 64Y-51117-00-00).

Part Number: TI-155-PMP-SL

Brass Press In Straight Pulse Line Nipple Fitting 1/4" Hose Barb. Use for dual carburetor setups with dual fuel pumps where a second pulse line is required.

Part Number: 01-02-530

The RRP Rickter Ninja Flow Guard is a performance part that was designed specifically for watercraft applications and especially for freestyle that Prevents the water flow to from the outside of the pump entering between the restriction nozzle and steering nozzle then breaking the flow water inside of the pump. Available for 144MM and 155MM Pumps. Fiberglass (Black), Carbon Fiber and TeXtreme Carbon (155MM Only).

The new XFS Ninja Competition G2 By Rickter for extreme freestyle! This new hull was designed for hard core freestyle but with adjustable ride features to assist learning by all rider skill levels. Purchase as equipped, or allow the Blowsion team to assemble your complete machine in multiple different engine and pump configurations. Email for detailed information and cost options.

PLEASE EMAIL FOR AVAILABILITY

The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-434

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Skat-Trak Stainless Steel Impeller for Yamaha 155MM Pumps. E-75-20 SWIRL.

Skat-Trak Stainless Steel Impeller for Yamaha 148MM Pumps. D-75-20 SWIRL.

The RRP Yamaha Freestyle Trim System for Yamaha 155mm & 160mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.

Part Number: 02-02-513

The RRP Yamaha Freestyle Trim System for Yamaha 144mm & 148mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.

Part Number: 02-02-510

The Cold Fusion Driveline Alignment Tool gives you a proper method and fixtures to center your pump to the mounting points of your mid-shaft assembly (half the battle) and it provides a method to insure the drive line is parallel to the mid-shaft and square to the firewall. Fits Yamaha style pump and midshaft assemblies.

Part Number: 04-04-064

Solas Yamaha Stainless Steel 148mm Impeller Housing for the Solas Yamaha 12 Vane 148mm Magnum Pump.

Part Number: 02-02-017

Solas has just introduced the 148mm Magnum 12 Vane Pump Stator Section. Fits all years Yamaha Super Jet and Blaster with use of standard length driveshaft. Constructed of stainless steel and 6061 T-6 billet aluminum, unlike the stock pumps, which are made from weaker cast aluminum, plastic and brass.

Part Number: 02-02-019

The RRP Rickter 155mm Aluminum Pump Shoe fits all Yamaha Superjet, 1993-1996 WaveBlaster 1, Rickter and most aftermarket Yamaha based hulls.

Part Number: 02-02-431

OEM Yamaha Pump Shoe Seal. Fits all OEM Yamaha, Skat-Trak and Solas 144mm Pumps.

Part Number: 6R7-51117-01-00