Search results for 'pump'

Vertex Mikuni SBN Check Valve Installation Tool. Used for installing check valve grommets on most Mikuni Super BN Carburetors and fuel pumps.

Part Number: 451470

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-434

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

The RRP Yamaha Freestyle Trim System for Yamaha 144mm & 148mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.

Part Number: 02-02-510

The best scoop grate on the market for clawing the maximum amount of water into the thirsty Polaris Octane Pump. The Jet Dynamics Top loader design is unbeatable for all around performance.

Part Number: 02-01-198

SOLAS Yamaha 12 Vane 144mm Stainless Magnum Pump. Fits all years Yamaha Superjet and WaveBlaster with standard length driveshaft. Pump Bearings and Seals Not Included.

Part Number: 02-02-020

The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.

Part Number: 02-02-407

The best scoop grate on the market for clawing the maximum amount of water into the thirsty 2008+ Super Jet pump. The Jet Dynamics Top loader design is unbeatable for all around performance.

Part Number: 02-01-154

Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!

Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-432

Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.

Part Number: 06-01-311

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001