Search results for 'bilge'

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits 1993-1996 Yamaha WaveBlaster 1 Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-107

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-106

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki JS440 and JS550 Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-105

Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). The bracket mounts to the lower two bolts of the driveshaft bearing carrier. Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki SXR 1500 Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-104

Billet Dash Plate Rotary Bilge Switch. Direct replacement for Kawasaki OEM plastic dash plates. Brushed finish. Bright dip anodized.

Part Number: 04-03-304

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-418

Replacement OEM bullet connectors now available at Blowsion. Kit includes 5 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-417

This cool universal anodized black aluminum mounting plate allows easy mounting of the rotary bilge switch as well as primer bulb on the dash. Specifically designed for the SXR but will work with other models. Inside mounting with the correct bulb style primer hole and rotary bilge switch ID means a sanitary install in minutes with no grinders or tubes of silicone needed.

Part Number: 04-06-002

Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.

Part Number: 06-01-201

Blowsion Bilge Switch Stop / Start Switch Mount - Yamaha. This sano billet switch assembly mounts directly to the bottom of the OEM Start / Stop switch housing of all Yamaha watercraft.

Part Number: 06-01-214

Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

Part Number: 06-01-212