Search results for 'Skat-Trak'
-
Skat-Trak Impeller Tool - Yamaha (25mm)
Skat-Trak Impeller Spline Tool Yamaha 25mm. Fits New style Skat-Trak impellers with splined front nose. Will not work on old style Skat-Trak impellers requiring a hex tool.
Part Number: RWRYAMSPSHO
Learn More -
Blowsion Rickter Edge Neon Green 701cc
This brand spankin new Rickter Edge FR has all the show and go to make a complete freeride weapon. Complete new build from the ground up with an OEM Yamaha 701 at the heart of it. Propelling the ski to launch and slash waves is a Billet 148mm Skat-Trak Magnum Set-Back pump. For rideability and reliability it has an OEM ignition system along with Factory Pipe Limited setup with VK Carbon Exhaust Chamber. Controls are all Blowsion, and the center of it is our Billet Lightweight Handlepole. This ski has just been put on display in the Blowsion showroom and is available to ship immediately!
Part Number: 10-01-064
Learn More -
OEM Yamaha Pump Rebuild Kit 155MM
Genuine 4-Piece OEM Yamaha Pump Rebuild Kit for 155MM Pumps. Fits OEM Yamaha 155mm and Skat-Trak Yamaha 75MM Hub Set-Back Pumps.
Part Number: 02-02-484
Learn More -
Skat-Trak Impeller - Kawasaki C-75 140MM
Skat-Trak Stainless Steel Impeller for Kawasaki 750 and SXR 800 Models. 140MM C-75MM Hub Swirl.
Learn More -
Skat-Trak Impeller - Yamaha E-75 155MM
Skat-Trak Stainless Steel Impeller for Yamaha 155MM Pumps. E-75-20 SWIRL.
Learn More -
Skat-Trak Impeller - Yamaha D-75 148MM
Skat-Trak Stainless Steel Impeller for Yamaha 148MM Pumps. D-75-20 SWIRL.
Learn More -
Skat-Trak Impeller - Yamaha C+75 144MM
Skat-Trak Stainless Steel Impeller for all Yamaha Superjet 144MM C+75-20 Swirl.
Learn More -
OEM Yamaha Pump Shoe Seal 144MM
OEM Yamaha Pump Shoe Seal. Fits all OEM Yamaha, Skat-Trak and Solas 144mm Pumps.
Part Number: 6R7-51117-01-00
Learn More -
Skat-Trak Set-Back Billet Magnum Pump - Yamaha
The Skat-Trak 14 Vane Two Piece Billet Set-Back Magnum Pump. Available in 148mm, 155mm, 158mm, and 160mm sizes. Includes one Skat-Trak impeller. Fits all years Yamaha Superjet, WaveBlaster and Rickter Models. Skat-Trak Extended Length Driveshaft is required.
-
Skat-Trak Trim Cable Long (Kawasaki Pulley System)
Skat-Trak Trim Cable Long for Kawasaki Pulley Systems. Fits all SXR 800 trim and tilt systems. Direct replacement for Skat Trak and Blowsion systems.
Part Number: 02-02-543
Learn More -
Blowsion Kustom Cut-Back Stainless Impellers
Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.
Learn More -
Skat-Trak Extended Driveshaft - Superjet
Skat-Trak Extended Drive Shaft for 1990-2007 Yamaha Superjet Models. For use with Skat-Trak Set-Back Magnum Pumps. Can be used with any standard Solas or Skat-Trak Impeller.
Part Number: 02-02-102
Learn More -
Skat-Trak Trim Cable Long (Yamaha Pulley System)
Skat-Trak Trim Cable Long for Yamaha Pulley Systems. Fits all Blowsion trim and tilt systems with pulley system. Direct replacement for Skat-Trak and Blowsion systems.
Part Number: 02-02-544
Learn More -
Pump Cone - Polaris / Magnum Pumps
The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.
Part Number: 02-02-407
Learn More