Search results for 'Sxr 800'

Mikuni High Performance Super BN 44mm Carburetor. Comes Complete with Extended Throttle Shaft and Choke Shaft Removed. Sold Each. BN44-40-8052

Part Number: 01-02-104

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

RRP Rickter Trim Lever. Available in Black, Blue, Red or Silver.

RRP Rickter Throttle Lever. Available in Black, Red, Blue or Silver.

Blowsion Adjustable T-Handle Factory Pipe Headpipe Water Screw Kit - Standard Size. T-Handle Design provides quick and easy adjustments for tuning. This kit is a direct replacement for those seized up water adjusting screws. Compatible with all Factory Headpipes.

Part Number: 01-01-741

Heavy Duty Stainless Steel Hose Clamp. Compatible with all 2.0" to 2.75" Inch (OD) Exhaust Couplers. Sold Each.

Part Number: 01-01-176

Billet aluminum throttle drum for maximum throttle adjustments. Machined from 6061-T6 aluminum and anodized for corrosion protection. Features 9 different hole locations for the throttle cable to attach. Now available in 5 different colors!

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.

Part Number: 01-02-598

Handle Pole Breather Tubing. Fits Blowsion, RRP, and other pole brackets. Available in 2.0" Inch or 2.25" Inch ID. Length: 24" (61cm) Sold Individually.

New Blowsion Turbulator Chin Pad. Specifically designed and form fit for the Blowsion Billet Handlepole. Custom Color options available!

The all new Universal OVP "Over the Pivot" Sealed Bearing Steering System. Fits all OEM Yamaha and Aftermarket Handlepoles (RRP/UMI/AC). Available in Black, Clear, Blue, Orange, Red and Green bright dip anodized colors!  PLEASE NOTE: The Universal OVP Steering System will only work with Fat Straight, Fat Riser or 4-Degree Fat Bars (sold separately). If you are installing on the OEM Yamaha Pole you will need to make extensive modifications to your OEM Chin pad mounting and location in order to clear the handlebars. The chin pad must be re-located further forward on the OEM Pole. You may want to consider the Standard Blowsion Steering System as it will clear the OEM Yamaha Chin Pad without any modifications.

Inline Water Filter. Made from impact resistant nylon with 3/8” barb ends. A clear bowl and removable filter screen allow easy inspection and cleaning.

Part Number: 01-01-780

RRP 4-Degree Bend Fat Bar with 28.6mm center for more clamping area. Constructed of -6061-T6 aluminum - black anodized with knurling on each end.

Part Number: 03-05-135

Dual Color Sheets of 1/4" (5.5mm) Hydro-Turf with Cut Diamond Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.