Search results for 'pump'

Oil / Fluid Extractor (6 Liter). This compact and easy to use oil/fluid extractor makes changing the oil on your 4-stroke model clean and hassle free. Sturdy portable container holds up to 6 liters (1.57 Gallons). Carry handle makes for easy transfer to recycling tank. Pump included.

Part Number: 06-04-088

The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-434

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Skat-Trak Stainless Steel Impeller for Yamaha 155MM Pumps. E-75-20 SWIRL.

Skat-Trak Stainless Steel Impeller for Yamaha 148MM Pumps. D-75-20 SWIRL.

Significantly reduces cavitation and improves overall performance. Constructed from aluminium for greater strength and durability. Suitable for Yamaha 2014+ SVHO. Suits all 4 Bolt 1.8 Yamaha Pump Models.

Part Number: WR06019

Adjustable Folding Aluminum Scissor Stand for Sit Down Watercraft. Allows the rider to elevate the ski in shallow water protecting the pump and bottom of the ski from damaging wave action.

Part Number: 06-05-009

The RRP Yamaha Freestyle Trim System for Yamaha 155mm & 160mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.

Part Number: 02-02-513

The RRP Yamaha Freestyle Trim System for Yamaha 144mm & 148mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.

Part Number: 02-02-510

The Cold Fusion Driveline Alignment Tool gives you a proper method and fixtures to center your pump to the mounting points of your mid-shaft assembly (half the battle) and it provides a method to insure the drive line is parallel to the mid-shaft and square to the firewall. Fits Yamaha style pump and midshaft assemblies.

Part Number: 04-04-064

The best scoop grate on the market for clawing the maximum amount of water into the thirsty Polaris Octane Pump. The Jet Dynamics Top loader design is unbeatable for all around performance.

Part Number: 02-01-198

The WORX Seadoo Spark Pump Plug Kit fills the unwanted cavities in the pump shoe that cause cavitation to improve acceleration and jet unit performance.

Part Number: WR0707

Solas Yamaha Stainless Steel 148mm Impeller Housing for the Solas Yamaha 12 Vane 148mm Magnum Pump.

Part Number: 02-02-017

Solas has just introduced the 148mm Magnum 12 Vane Pump Stator Section. Fits all years Yamaha Super Jet and Blaster with use of standard length driveshaft. Constructed of stainless steel and 6061 T-6 billet aluminum, unlike the stock pumps, which are made from weaker cast aluminum, plastic and brass.

Part Number: 02-02-019

The RRP Rickter 155mm Aluminum Pump Shoe fits all Yamaha Superjet, 1993-1996 WaveBlaster 1, Rickter and most aftermarket Yamaha based hulls.

Part Number: 02-02-431