Search results for 'bilge'
-
OEM Bullet Terminals - 5 Pack
Replacement OEM bullet connectors now available at Blowsion. Kit includes 5 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.
Part Number: 01-04-417
Learn More -
OEM Bullet Terminals - 20 Pack
Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.
Part Number: 01-04-418
Learn More -
Recessed Dash Mount
New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Dash Plate Rotary Bilge Switch - Kawasaki 750
Billet Dash Plate Rotary Bilge Switch. Direct replacement for Kawasaki OEM plastic dash plates. Brushed finish. Bright dip anodized.
Part Number: 04-03-304
Learn More -
Bilge Pump Mount - Kawasaki SXR 1500
The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). The bracket mounts to the lower two bolts of the driveshaft bearing carrier. Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki SXR 1500 Models. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-104
Learn More -
Bilge Fitting Pro
Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.
Learn More -
Blowsion Dash Fitting
Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.
Learn More -
Bilge Pump Mount - Kawasaki JS440/550
The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki JS440 and JS550 Models. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-105
Learn More -
Bilge Pump Mount - Kawasaki 550/650/750SX
The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-106
Learn More -
Bilge Pump Mount - Yamaha WaveBlaster
The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits 1993-1996 Yamaha WaveBlaster 1 Models. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-107
Learn More