Search results for 'pump'

Check out that mat kit! This 2022 Rickter Edge has a one of a kind GatorStep mat kit in a beautiful brushed grey and teal to match the vibrant custom graphics kit. Teal Blowsion Billet pieces complete the look on this ready-to-rip ski. With a 1000cc Dasa Powervalve engine and a SOLAS Yamaha Magnum Pump 148MM, this ski performs and handles awesome on flat water or surf. Available for immediate shipment, this ski is currently in our Blowsion Showroom.

Part Number: 10-01-072

Brand new Rickter Edge for sale! Powered by a DASA 850cc Engine and SOLAS 148mm Magnum Pump. Every part, upgrade is OEM or better quality. Assembled and power tuned this ski is bulletproof and can handle all riding environments with ease.

Part Number: 10-01-070

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

This brand spankin new Rickter Edge FR has all the show and go to make a complete freeride weapon. Complete new build from the ground up with an OEM Yamaha 701 at the heart of it. Propelling the ski to launch and slash waves is a Billet 148mm Skat-Trak Magnum Set-Back pump. For rideability and reliability it has an OEM ignition system along with Factory Pipe Limited setup with VK Carbon Exhaust Chamber. Controls are all Blowsion, and the center of it is our Billet Lightweight Handlepole. This ski has just been put on display in the Blowsion showroom and is available to ship immediately!

Part Number: 10-01-064

Blowsion Stainless Steel Pump Bolt Kit for Yamaha 155mm Pump Conversions with threaded wear ring. The Socket Head Bolt design allows for use of hex key tool which results in much easier access. Kit Includes 4 Bolts.

Part Number: 02-02-479

Blowsion Stainless Steel Pump Bolt Kit for all Yamaha Superjet and Rickter Models. The Socket Head Bolt design allows for use of hex key tool which results in much easier access. A Great replacement for OEM Yamaha Part Number: 90119-10948-00. Kit Includes 4 Bolts and 4 Washers.

Part Number: 02-02-478

Brass Press In Straight Pulse Line Nipple Fitting 1/4" Hose Barb. Use for dual carburetor setups with dual fuel pumps where a second pulse line is required.

Part Number: 01-02-530

The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-434

Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Yamaha Superjet.

Part Number: 02-02-406

Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!

Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.

Part Number: 01-02-557

Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-432

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.