Search results for 'Kawasaki'

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.

Part Number: 01-02-598

Handle Pole Breather Tubing. Fits Blowsion, RRP, and other pole brackets. Available in 2.0" Inch or 2.25" Inch ID. Length: 24" (61cm) Sold Individually.

Blowsion Pole Bracket Plate. Required when installing a Blowsion Billet Handlepole on an older (PRE-2014 DESIGN) Blowsion Dual Hole Handle Pole Bracket. Fits 1996-2020 Yamaha Superjet, 1994-1995 Yamaha FX1, 2002-2004 Polaris Octane, and Kawasaki 750 Models.

Part Number: 03-04-067

New Blowsion Turbulator Chin Pad. Specifically designed and form fit for the Blowsion Billet Handlepole. Custom Color options available!

Blowsion Stainless Steel Steering Cable Extension. Compatible with all OEM Yamaha and OEM Kawasaki 5mm Steering Cable Ends.

Part Number: 03-04-210

The all new Universal OVP "Over the Pivot" Sealed Bearing Steering System. Fits all OEM Yamaha and Aftermarket Handlepoles (RRP/UMI/AC). Available in Black, Clear, Blue, Orange, Red and Green bright dip anodized colors!  PLEASE NOTE: The Universal OVP Steering System will only work with Fat Straight, Fat Riser or 4-Degree Fat Bars (sold separately). If you are installing on the OEM Yamaha Pole you will need to make extensive modifications to your OEM Chin pad mounting and location in order to clear the handlebars. The chin pad must be re-located further forward on the OEM Pole. You may want to consider the Standard Blowsion Steering System as it will clear the OEM Yamaha Chin Pad without any modifications.

Inline Water Filter. Made from impact resistant nylon with 3/8” barb ends. A clear bowl and removable filter screen allow easy inspection and cleaning.

Part Number: 01-01-780

Give the gift of Blowsion! Use for gifting Blowsion parts and services. Specify the dollar amount of your gift in the order space listed in the dropdown menu below.

Finish the look of your engine compartment with Blowsion specialty colored 3/8" water cooling hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.

Finish the look of your engine compartment with Blowsion specialty colored 1/4" fuel hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.

Finish the look of your engine compartment with Blowsion specialty colored 1/8" fuel primer hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot.

Replacement Delrin pivot bolt bushings for the Blowsion Billet Handlepole. Both Kawasaki and Yamaha options available. Quantity two bushings included per kit.

Part Number: 03-04-116

Universal Fuel Pickup Filter. Add some of these for extra fuel filtration and also keeps the fuel in your lines when going upside down.

Part Number: 01-02-449

Designed to work in conjunction with smaller battery case sizes. Great for aftermarket hull builds and small Superjet battery replacement. Battery Strap location has been relocated to avoid interference with battery terminals. Also compatible with many other batteries. Check the dimensions of your battery to insure proper fitment. Welded Aluminum Grain Finish. Color: Anodized Black.

Part Number: 01-04-602