Search results for 'pump'
-
Bilge Fitting 45-Degree
Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.
Learn More -
Bilge Fitting Straight
Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.
Learn More -
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More -
Bilge Pump Hose - 10FT
Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-302
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
Billet Carburetor Block Off
Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.
Part Number: 01-02-557
Learn More -
Blowsion Billet Trim Lever
Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!
Learn More -
Cold Fusion Driveshaft Alignment Tool - Yamaha
The Cold Fusion Driveline Alignment Tool gives you a proper method and fixtures to center your pump to the mounting points of your mid-shaft assembly (half the battle) and it provides a method to insure the drive line is parallel to the mid-shaft and square to the firewall. Fits Yamaha style pump and midshaft assemblies.
Part Number: 04-04-064
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Mikuni Pop-Off Pressure Gauge 30PSI
Genuine Mikuni Pop-Off Pressure Gauge 30PSI. Gauge gives accurate pop-off pressure readings. This high pressure pump is durable and easy to use. A must have tool for tuning your carbs.
Part Number: 06-04-012
Learn More -
Bilge Fitting Pro
Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.
Learn More -
OEM Yamaha Steering Cable Stopper
OEM Yamaha Steering Cable Stopper. This plastic stopper clip attaches to steering cable on the pump side to hold it in place.
Part Number: EU0-61486-00-00
Learn More -
OEM Yamaha Steering Cable Stopper Seal
OEM Yamaha Steering Cable Stopper Seal. This rubber seal slides onto the pump side steering cable and prevents water from entering the hull.
Part Number: EU0-61435-00-00
Learn More -
OEM Yamaha Steering Cable Connector Body
OEM Yamaha Steering Cable Connector Body. This plastic through hull fittings screws into the pump side of the hull and allows the steering cable to pass through.
Part Number: EU0-61436-00-00
Learn More -
Vertex Mikuni Check Valve Install Tool
Vertex Mikuni SBN Check Valve Installation Tool. Used for installing check valve grommets on most Mikuni Super BN Carburetors and fuel pumps.
Part Number: 451470
Learn More