Search results for 'pump'
-
Bilge Fitting 45-Degree
Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.
Learn More -
Bilge Fitting Straight
Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.
Learn More -
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More -
Bilge Pump Hose - 10FT
Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-302
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
Blowsion Pump Shoe - Yamaha 144MM
Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.
Part Number: 02-02-432
Learn More -
Blowsion Billet Trim Lever
Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!
Learn More -
Jet Dynamics Intake Grate - Superjet 2008+
The best scoop grate on the market for clawing the maximum amount of water into the thirsty 2008+ Super Jet pump. The Jet Dynamics Top loader design is unbeatable for all around performance.
Part Number: 02-01-154
Learn More -
Pump Cone - Polaris / Magnum Pumps
The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.
Part Number: 02-02-407
Learn More -
Solas Yamaha Magnum Pump 144MM
SOLAS Yamaha 12 Vane 144mm Stainless Magnum Pump. Fits all years Yamaha Superjet and WaveBlaster with standard length driveshaft. Pump Bearings and Seals Not Included.
Part Number: 02-02-020
Learn More -
Jet Dynamics Intake Grate - Octane
The best scoop grate on the market for clawing the maximum amount of water into the thirsty Polaris Octane Pump. The Jet Dynamics Top loader design is unbeatable for all around performance.
Part Number: 02-01-198
Learn More -
RRP Tilt Kit - Yamaha 144MM
The RRP Yamaha Freestyle Trim System for Yamaha 144mm & 148mm style pumps is a super easy top pull trim system and was designed to be effortless and allowing for better rider control during maneuvers and tricks.
Part Number: 02-02-510
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Blowsion Pump Shoe - Yamaha 148MM
The Blowsion 148mm Aluminum Pump Shoe was designed for fitting larger 148mm pumps into both Yamaha Superjet and aftermarket hulls. Using our 148mm shoe vs a 144mm (stock Superjet size) will greatly increase hook up and drive when used in conjunction with 148mm pumps. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so installation in the different Yamaha design aftermarket hulls can be facilitated.
Part Number: 02-02-434
Learn More -
Bilge Fitting Pro
Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.
Learn More