Search results for 'Hose'

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Blowsion Heavy Duty Elbow Coupling. Super Durability tested Blowsion manufactured pipe elbow replaces the weak existing elbows on the market.

Part Number: 01-01-708

Replace your rear factory hood latch with a billet aluminum BLOWSION latch and ride worry free. Recently updated and re-machined to also fit the Kawasaki SXR 800 and SXR 1500. Also fits all years Yamaha FX1 and all years Yamaha Super Jet. A must for surf and big wave riders, especially those running a BLOWSION pole limiting rope. Requires the stock base locking hardware. Now available in more colors- Anodized Green, Red, Blue, Orange, Clear, Purple and Black!

Introducing Long John Silver. Extended Length Bow Eye Bushing for those custom install rear mat kick wedges or thick tray undermat. One extra full inch of thread guarantees plenty of material to nut up to! Offered in Anodized Black and Clear.

Blowsion standard size stainless headpipe screw kits. Replace those always corroded and plugged FP water adjusting screws!

Part Number: 01-01-740

Blowsion manufactured Factory Pipe replacement coupler. This double compound thickness heavy duty silicone exhaust coupler fits "A" and "B" Headpipes including Kawasaki, Yamaha and Polaris Wet pipes. (DIMENSION 4"X 2 1/8") This is NOT the thin blue coupler model offered by other suppliers, but a spec manufactured Blowsion coupler made out of hi-heat silicone hose.

Part Number: 01-01-703

100mm-120mm Heavy Duty Stainless Steel Hose Clamp. Fits both SXR Wet Pipe, and all Yamaha B-Pipe Silicone Couplers. Sold Each.

Part Number: 01-01-723

The preferred choice for fuel filters and water separators. Fits all Yamaha Standups. Can be used also with KAWI and Polaris Octane models. 1/4" Inlet/Oulet hose size.

Part Number: 01-02-551

Direct water and air to where you want it in the engine compartment! Drop Tube and Urethane Flange for Hood Baffle Air Intakes. Use with either aftermarket hoods or stock factory hood to increase air flow. Each kit includes three oversize lengths of hose tubing and urethane flanges. Bond-able to hand laid fiberglass, carbon, SMC or ABS inner liners these are simple to install and are an excellent answer for air-starved motors. An EXCELLENT choice for the Kawasaki SXR 800 with the Factory Pipe installed!

Part Number: 05-02-199

These Blowsion machined bypass fittings are angled at 45 degrees of flow. Fits 3/8" ID Hose. Offered in Anodized Clear, Black, Red, Blue, Orange and Green.

Blowsion Billet 90-Degree Water Bypass fittings. Fits 3/8" ID Cooling Hoses. Offered in Anodized Clear, Black, Green, Red, Blue and Orange. All Colors In stock!

WORX Extended Ride Plate for 1990-2007 Yamaha Superjet with "D" Cut-out. The extra length obviously holds the boat a lot flatter also and with the hard chine lines on the edges of the plate makes it a lot easier to carve those really tight turns in complete control.

Part Number: WR305

Replacement OEM bullet connectors now available at Blowsion. Kit includes 5 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-417

Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-418