Search results for 'pump'
-
Bilge Fitting 45-Degree
Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.
Learn More -
Bilge Fitting Straight
Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.
Learn More -
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More -
Bilge Pump Dual Mount - Kawasaki
Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-101
Learn More -
Bilge Pump Hose - 10FT
Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-302
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
Bilge Pump Single Mount - Kawasaki
Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-102
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
Billet Carburetor Block Off
Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.
Part Number: 01-02-557
Learn More -
Blowsion Billet Trim Lever
Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!
Learn More -
Pump Cone - Kawasaki
Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Kawasaki SXR, 750SX, SXI, SXi-Pro, X2 and 650SX Models.
Part Number: 02-02-405
Learn More -
Solas Kawasaki Mag Pump/Tilt Combo
Solas 140mm Kawasaki 12 Vane Stainless Standard Pump with Adjustable diameter Drop Nozzle Trim System.
Part Number: 02-02-021
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Pulse Line Fitting 1/4"
Brass Press In Straight Pulse Line Nipple Fitting 1/4" Hose Barb. Use for dual carburetor setups with dual fuel pumps where a second pulse line is required.
Part Number: 01-02-530
Learn More -
Mikuni Pop-Off Pressure Gauge 30PSI
Genuine Mikuni Pop-Off Pressure Gauge 30PSI. Gauge gives accurate pop-off pressure readings. This high pressure pump is durable and easy to use. A must have tool for tuning your carbs.
Part Number: 06-04-012
Learn More -
OEM Kawasaki Pump Trim Seal
Genuine OEM Kawasaki Pump Trim Seal. Fits all Kawasaki 750 and SXR 800 models.
Part Number: 39145-3735
Learn More