Search results for 'mat'
-
Bilge Pump - Rule - 500GPH
Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!
Part Number: 06-01-001
Learn More -
Bilge Pump Dual Mount - Kawasaki
Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-101
Learn More -
Bilge Pump Single Mount - Kawasaki
Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-102
Learn More -
Blowsion SXR Heavy Duty Steering Cable
The Blowsion Heavy Duty steering cable incorporates Blue Max control cable construction. This superior control cable material is born of marine and aviation engineering design, with extreme low friction and minimal loss of motion. The Blowsion Heavy Duty replacement steering cable fits all years Kawasaki SXR 800. Overall Length: 122.00" (Inches).
Part Number: 02-05-303
Learn More -
Blowsion Hood Hooks - SXR
Utilizing our many years of Super Jet Freestyle and surf quality hood hook design experience, these bulletproof SXR billet hood hooks allow for the ultimate abuse of your 2003 and newer Kawasaki SXR 800 and SXR 1500 on the race course, river or in big surf. Do not risk losing your hood -- no more tweaked or broken OEM clips bending or breaking and causing serious engine and wallet damage. Includes Stainless Steel Mounting Hardware. Color: Anodized Black.
Part Number: 04-04-101
Learn More -
Bow Eye Bushing - Extended
Introducing Long John Silver. Extended Length Bow Eye Bushing for those custom install rear mat kick wedges or thick tray undermat. One extra full inch of thread guarantees plenty of material to nut up to! Offered in Anodized Black and Clear.
Learn More -
DASA Cylinder Head Dome 89MM-94MM
DASA Billet Cylinder Head Dome for 89MM-94MM bore sizes. Fits DASA Billet Cylinder Heads. Sold Each. Learn More -
OEM Pro Honda Dielectric Grease
Put this 0.5 ounce tube of miracle gel in your toolbox! This is the cure for for scattered spark resulting form moisture and corrosion of your spark plug ends and boots.
Part Number: 08798-0001
Learn More -
Duckbill One Way - Replacement
Replaces your worn out rubber duckbill. Includes color-matched Zip Tie.
Part Number: 06-01-010
Learn More -
FP Headpipe Water Screw Kit - Oversized
Blowsion Oversized Factory Pipe Headpipe Screw Kit. Drill out and replace your corroded and plugged water adjusting screws. Compatible with all Factory Headpipes
Part Number: 01-01-742
Learn More -
Engine Flush Kit - Single Outlet
All metal and stainless construction. Easy to use. Just push in to your 45 degree or 90 degree aftermarket aluminum water bypass(es). Backflush away!
Part Number: 06-04-001
Learn More -
Hydro-Turf Kick Wedge 1"
Add a kick tail to your watercraft bottom mat area with this 1" wedge. Helps to keep the riders back foot from slipping out of the tray and getting weight farther forward.
Part Number: 04-02-345
Learn More -
Hydro-Turf Sheet - Diamond
Hydro-Turf 40" x 62" Diamond Groove sheet material. Blowsion stocks all available colors and groove options listed. We are overflowing with turf!
See our special formulated solvent-based Mat Glue for Installation.
Learn More -
Hydro-Turf Sheet - Waffle
Hydro Turf 40" x 49" Waffle Groove sheet material. Blowsion stocks all available colors listed. We are overflowing with turf!
See our special formulated solvent-based Mat Glue for Installation.
Learn More -
Installation Materials Kit - Footwells / Hull Reinforcement
Each kit includes all materials needed for mixing into, and handling, your installation resin (available separately). Silica Thickener, Mixing Cups, Brushes, Gloves and Knitted fabric cloth for all seams.
Part Number: 06-03-113
Learn More -
Blowsion Kick Plate
An ultra bitchin' way to keep your rear edge tray mat wrapped and sealed down. Excellent solution to a problem area for all mat installations. Available for all models.
Learn More