Search results for 'Year'

Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-432

Blowsion Billet Choke Knob. Direct replacement for YAMAHA OEM Plastic choke knob. Installs with OEM set screw (Not Included). Fits all Years Yamaha Superjet, FX1 and WaveBlaster Models. Bright Dip Anodized Black.

Part Number: 04-03-351

Sanitize the dash of your Yamaha controls with this Blowsion Billet Dash Knob. Replaces the OEM Yamaha plastic ON/OFF/RESERVE Knob. Uses OEM screw to mount. Fits all years Yamaha Superjet, FX1 and WaveBlaster Models. Also Compatible with most Yamaha 2-Stroke Sitdown Models (Wave Jammer, Wave Runner, Wave Raider, VXR). Bright Dip Anodized Black. 1 Per Package.

Part Number: 04-03-352

Available for riders wanting to use the end flange only for custom scupper and rear exhaust installations etc. The new billet flange assembly is the premium design setup and allows use of the Blowsion billet exhaust outlet so vain riders can sanitize both sides of the rear of their watercraft. Fits all years Super Jet, KAWI 750 and SXR 800, KAWI 650, and Polaris Octane. Anodized Clear.

Part Number: 06-01-023

Engine Block Off Plates 62T. A great way to block off access to your internal motor and all its complex innards. No more red rags or cheesy paper towels to suck through your initial engine fire off and carpet the cases with! Cool way for storing and displaying motors. Carbon Black Anodized and includes all mounting hardware. Fits all years 62T 701cc Yamaha two cylinder motors.

Part Number: 01-03-813

Get rid of that unsightly gauge window on the side of your Blaster with this sano billet piece. Installs with the OEM mounting hardware. Fits all years Yamaha WaveBlaster.

Part Number: 05-04-450

Jet Dynamics 155mm over-sized aluminum replacement intake duct. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Rickter and many other popular Yamaha based aftermarket hulls. *Intended for Use with Larger 155mm Yamaha Pumps.

Part Number: 02-05-432

More juice for your powerplant than any OEM coil can provide. New Updated model! Fits all years Yamaha Superjet 650/701/760, and Kawasaki 750 and 800 SXR.

Part Number: 01-05-012

Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Yamaha Superjet.

Part Number: 02-02-406

SOLAS Yamaha 12 Vane 144mm Stainless Magnum Pump. Fits all years Yamaha Superjet and WaveBlaster with standard length driveshaft. Pump Bearings and Seals Not Included.

Part Number: 02-02-020

6mm Throttle Cable Adapter. A Throttle Cable Adapter is required to run most aftermarket throttle levers. Fits All Years Yamaha Two Stroke and 2021+ Yamaha Superjet PWC Models. Please see list below for model compatibility.

Part Number: 03-05-242

This is a similar grate to the WR201 however it is less aggressive and gives 1-2 MPH higher top speed but does not have the same braking effect as the WR201. If you want top speed and usually ride in calmer/smoother water this is the one for you. Perfectly matched to enable easy installation. Fits all years 1990-2017 Yamaha Superjet and WaveBlaster 1, 2.

Part Number: WR205

Genuine 3 Piece OEM Yamaha Crank Seal Kit. fits all years yamaha 701/760/850/DASA Engines.

Part Number: 02-02-487

OEM Yamaha 144mm Pump Impeller Housing. Fits all years Yamaha Superjet, WaveBlaster 1 and Rickter Hull Models.

Part Number: 6R7-51312-03-94 / 6R7-51312-03-00

OEM Yamaha Drive Coupler Cover. Fits All Years Yamaha Superjet, FX1, Waveblaster and Rickter Models.

Part Number: 61X-51381-00-00