Search results for 'Kawasaki'
-
Marine Sealant Tube - White (240ML)
The key to installing Tubbie Sponsons, Railcaps and other composite accessories on your watercraft. Easy-to-use tube fits a standard caulking gun. Fast-set formula dries tack-free in 90 minutes and delivers extremely tough bonds. Color: White.
Part Number: 06-03-135
Learn More -
Blowsion Mat Glue - Pint
Blowsion Mat Kit Glue "Blow Goo" to the rescue. Use this solvent-based contact adhesive with your Hydro Turf or stitched mat kit and never worry again about your mats coming loose. Not water-based!
Part Number: 06-03-141
Learn More -
Blowsion Mat Glue - Quart
Blowsion Mat Kit Glue "Blow Goo" to the rescue. Use this solvent-based contact adhesive with your Hydro Turf or stitched mat kit and never worry again about your mats coming loose. Not water-based!
Part Number: 06-03-142
Learn More -
Mikuni Adjusting T Screws - Kawasaki
Mikuni high and low-speed carburetor adjuster screws with "T" cross bar - extended length for easy adjustments. Absolutely a must when running aftermarket pipes.
Part Number: 01-02-540
Learn More -
Throttle Cable Bracket - Diaphragm Mount
Mikuni Diaphragm Mount throttle cable bracket. Trick mounting setups are enabled with this handy bracket. Stainless Steel Mounting Hardware Included. Now available in two sizes.
Learn More -
ODI Blowsion Lock Ring End Caps
ODI Grip Blowsion Logo Lock Ring End Cap Combo- now you can have the anodized bling look all the way through to the end cap. Each kit includes inner lock rings, and outer lock ring/caps w/ hardware.
Learn More -
Oil Injection Block Off Plate
Oil block-off plates allow for an easy conversion from factory oil injection to pre-mixing your own fuel. Block-off plates fit all Yamaha 650701/760 and Kawasaki 650/750 Models. Hardware included. Anodized Black.
Part Number: 01-03-812
Learn More -
Primer Kit - Keihin Dual
Fits 8mm choke shaft Keihin dual carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and bulletproof plunger. Get rid of that worthless factory choke and apply a direct shot of fuel!
Part Number: 01-02-404
Learn More -
Primer Kit - Keihin Single
Fits 8mm choke shaft Keihin single carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and bulletproof plunger. Get rid of that worthless factory choke and apply a direct shot of fuel!
Part Number: 01-02-403
Learn More -
Primer Kit - Mikuni Dual
Fits 6mm choke shaft Mikuni dual carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and bulletproof plunger.
Part Number: 01-02-402
Learn More -
Primer Bulb
Try the sanitary "non foot destroying" rubber-based bulb type primer. In stock and ready to flow! Pair with the Blowsion Dash Fitting for best protection.
Part Number: 01-02-411
Learn More -
Primer Piston
The tried-and-true plunger style primer. In stock and ready to flow!
Part Number: 01-02-410
Learn More -
Pump Cone - Kawasaki
Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Kawasaki SXR, 750SX, SXI, SXi-Pro, X2 and 650SX Models.
Part Number: 02-02-405
Learn More -
Rotary Bilge Switch - 3 Position
Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.
Part Number: 06-01-201
Learn More -
Small Fuel Tank - For PF/RRP Pipe
Reduced size 8.5 Liter (2.25 Gal) fuel tank. Less weight- required when using TNT, RRP or PowerFactor Pipes. Specially designed fuel tank incorporates lower baffle section to reduce fuel sloshing guaranteeing uninterrupted fuel supply. Comes equipped with Dual Fuel Pickups, Fuel Pickup Filters and Fuel Tank Fittings for Gas Tank Vent and Return Lines.
Learn More -
Stainless Hood Latch Assembly
Fits all Kawasaki 650, 750, SXR and GEN2 X2 800 Models. Comes complete with latch assembly and hood clip. 100% polished stainless. Trick and functional. Why incur the factory OEM replacement expense?
Part Number: 04-04-030
Learn More