Search results for 'pump'

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-101

Blowsion Dual Bilge Pump Mounting Bracket. The bracket locates the pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. Fits 1994 and up Yamaha Superjet Models. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-153

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-102

Single bilge pump mounting bracket for all 1994 and newer Yamaha SuperJet Models. The bracket locates the bilge pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-152

Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-432

Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.

Part Number: 01-02-557

Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!

Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Kawasaki SXR, 750SX, SXI, SXi-Pro, X2 and 650SX Models.

Part Number: 02-02-405

Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Yamaha Superjet.

Part Number: 02-02-406

The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.

Part Number: 02-02-407

Adjustable Folding Aluminum Scissor Stand for Sit Down Watercraft. Allows the rider to elevate the ski in shallow water protecting the pump and bottom of the ski from damaging wave action.

Part Number: 06-05-009