Search results for 'MAgnum'
-
Impros Hooker Impeller - Yamaha 144MM
The Impros Hooker 144mm impeller for the Yamaha is a 3-blade large hub diameter, radial edge design stainless steel impeller designed and intended for Bottom end and “Hook up” for Freestyle and Freeriders on a SuperJet, Blaster, or similar ski that utilizes the 144mm pump and want maximum AIR for tricks.
Learn More -
Solas KGX Pump Rebuild Kit SXR 1500
Solas Magnum Pump Bearing Seal Rebuild kit for Kawasaki SXR 1500 KGX Pumps. Includes bearings and Seals.
Part Number: 02-02-026
Learn More -
Solas Magnum Pump Assembly - Kawasaki SXR 1500
The Solas KGX-PM-148/74T 12-Vane Stainless Steel Jet Pump is a direct bolt-on performance upgrade. The one-piece, investment cast stainless steel pump offers increased bottom-end acceleration, improved hook-up, and up to 2mph top speed gain over the OEM pump. Oversized bearing housing supports and includes 3 high-quality sealed bearings, seals, shaft and billet aluminum pump cone. Complete Kit includes reduction nozzle and return assisted trim/steering nozzle along with interchangeable nozzle rings for fine tuning.
Part Number: 02-02-025
Learn More -
Solas Magnum Pump - Kawasaki SXR 1500
The SOLAS 12 Vane Stainless Steel Magnum Pump is a direct bolt-on performance upgrade. The one piece investment cast stainless steel pump offers improved bottom end acceleration, improved hook-up, and up to 2 mph top speed gain over the OEM Kawasaki SXR 1500 pump. Pump Includes bearings, seals, shaft and pump cone.
Part Number: 02-02-024
Learn More -
Solas Yamaha Impeller Housing 148MM
Solas Yamaha Stainless Steel 148mm Impeller Housing for the Solas Yamaha 12 Vane 148mm Magnum Pump.
Part Number: 02-02-017
Learn More -
Solas Yamaha Magnum Pump 148MM
Solas has just introduced the 148mm Magnum 12 Vane Pump Stator Section. Fits all years Yamaha Super Jet and Blaster with use of standard length driveshaft. Constructed of stainless steel and 6061 T-6 billet aluminum, unlike the stock pumps, which are made from weaker cast aluminum, plastic and brass.
Part Number: 02-02-019
Learn More -
Skat-Trak Set-Back Billet Magnum Pump - Yamaha
The Skat-Trak 14 Vane Two Piece Billet Set-Back Magnum Pump. Available in 148mm, 155mm, 158mm, and 160mm sizes. Includes one Skat-Trak impeller. Fits all years Yamaha Superjet, WaveBlaster and Rickter Models. Skat-Trak Extended Length Driveshaft is required.
-
Solas Kawasaki Mag Pump/Tilt Combo
Solas 140mm Kawasaki 12 Vane Stainless Standard Pump with Adjustable diameter Drop Nozzle Trim System.
Part Number: 02-02-021
Learn More -
Blowsion Kustom Cut-Back Stainless Impellers
Increased acceleration, bottom end hook-up and hi-rev grunt are only a few of the advantages of the revolutionary Blowsion Large Magnum Hub cut-back impellers now being offered.
Learn More -
Skat-Trak Extended Driveshaft - Superjet
Skat-Trak Extended Drive Shaft for 1990-2007 Yamaha Superjet Models. For use with Skat-Trak Set-Back Magnum Pumps. Can be used with any standard Solas or Skat-Trak Impeller.
Part Number: 02-02-102
Learn More -
Solas Yamaha Magnum Pump 144MM
SOLAS Yamaha 12 Vane 144mm Stainless Magnum Pump. Fits all years Yamaha Superjet and WaveBlaster with standard length driveshaft. Pump Bearings and Seals Not Included.
Part Number: 02-02-020
Learn More -
Pump Cone - Polaris / Magnum Pumps
The Freestyle Pump Cone is designed to improve low end and mid-range punch for better tricks. Lets your engine rev faster in the mid-range. A MUST for serious low end. Fits all Polaris Octane and Yamaha Skat-Trak/Solas Magnum Pumps ONLY.
Part Number: 02-02-407
Learn More