Search results for 'ODI'

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Blowsion Dual Bilge Pump Mounting Bracket. The bracket locates the pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. Fits 1994 and up Yamaha Superjet Models. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-153

Single bilge pump mounting bracket for all 1994 and newer Yamaha SuperJet Models. The bracket locates the bilge pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-152

Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

Part Number: 06-01-212

Blowsion Billet Choke Knob. Direct replacement for YAMAHA OEM Plastic choke knob. Installs with OEM set screw (Not Included). Fits all Years Yamaha Superjet, FX1 and WaveBlaster Models. Bright Dip Anodized Black.

Part Number: 04-03-351

Blowsion Low Pro Billet aluminum fuel caps for all Yamaha watercraft. Low profile smooth design allows for outside fueling, yet will not get in the way during aerial or freestyle moves around the front of the watercraft. Available in all anodized colors!

Sanitize the dash of your Yamaha controls with this Blowsion Billet Dash Knob. Replaces the OEM Yamaha plastic ON/OFF/RESERVE Knob. Uses OEM screw to mount. Fits all years Yamaha Superjet, FX1 and WaveBlaster Models. Also Compatible with most Yamaha 2-Stroke Sitdown Models (Wave Jammer, Wave Runner, Wave Raider, VXR). Bright Dip Anodized Black. 1 Per Package.

Part Number: 04-03-352

Available for riders wanting to use the end flange only for custom scupper and rear exhaust installations etc. The new billet flange assembly is the premium design setup and allows use of the Blowsion billet exhaust outlet so vain riders can sanitize both sides of the rear of their watercraft. Fits all years Super Jet, KAWI 750 and SXR 800, KAWI 650, and Polaris Octane. Anodized Clear.

Part Number: 06-01-023

Replace your rear factory hood latch with a billet aluminum BLOWSION latch and ride worry free. Recently updated and re-machined to also fit the Kawasaki SXR 800 and SXR 1500. Also fits all years Yamaha FX1 and all years Yamaha Super Jet. A must for surf and big wave riders, especially those running a BLOWSION pole limiting rope. Requires the stock base locking hardware. Now available in more colors- Anodized Green, Red, Blue, Orange, Clear, Purple and Black!

Blowsion machined aluminum bow eye bushings protect the hull when trailering. Offered in Anodized Clear, Black, Green, Red, Blue, Purple and Orange. All Colors In stock!

Introducing Long John Silver. Extended Length Bow Eye Bushing for those custom install rear mat kick wedges or thick tray undermat. One extra full inch of thread guarantees plenty of material to nut up to! Offered in Anodized Black and Clear.

These Blowsion machined bypass fittings are angled at 45 degrees of flow. Fits 3/8" ID Hose. Offered in Anodized Clear, Black, Red, Blue, Orange and Green.

Blowsion Billet 90-Degree Water Bypass fittings. Fits 3/8" ID Cooling Hoses. Offered in Anodized Clear, Black, Green, Red, Blue and Orange. All Colors In stock!

Blowsion Billet Hood Finger Pull. Direct replacement for OEM Yamaha Superjet plastic hood finger pulls. Fits all 1990-2020 OEM Yamaha Superjet Hoods. Replaces factory plastic clip. Stellar function and look! Bright dip anodized Black.

Part Number: 04-03-353