Search results for 'Kawasaki'

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001

Replace your rear factory hood latch with a billet aluminum BLOWSION latch and ride worry free. Recently updated and re-machined to also fit the Kawasaki SXR 800 and SXR 1500. Also fits all years Yamaha FX1 and all years Yamaha Super Jet. A must for surf and big wave riders, especially those running a BLOWSION pole limiting rope. Requires the stock base locking hardware. Now available in more colors- Anodized Green, Red, Blue, Orange, Clear, Purple and Black!

The Proform footstrap is the most flexible of DAKINE model footstraps and is commonly the most preferred for riders who ride barefoot.

Part Number: 04-02-336

Dakine Primo Freeriding foot straps can be easily adjusted on or off the water for all foot sizes and riders. Great for riders looking for that Joe Kenney or Pierre Maxient wave-shred style of surfriding.

Part Number: 04-02-335

Hydro-Turf 40" x 62" Diamond Groove sheet material. Blowsion stocks all available colors and groove options listed. We are overflowing with turf!

See our special formulated solvent-based Mat Glue for Installation.

Hydro Turf 40" x 49" Waffle Groove sheet material. Blowsion stocks all available colors listed. We are overflowing with turf!

See our special formulated solvent-based Mat Glue for Installation.

The RRP Adjustable Hood Latch is made from billet aluminium 6061 t6. This adjustable hood latch gives you the possibility to adjust the amount of pressure applied on the hood seal in a second. Extremely strong design eliminating failure of the latch and danger of losing hood and the ability of sinking the ski. Available in Red, Black, Blue, Green.

Extended Length. Made out of injection molded flexible urethane. Attaches to your watercraft with its own adhesive backing. Each kit includes special pre-wipe cleaner to promote maximum adhesion and durability. The 1-3/8" Inch size is excellent for most sitdown PWC as well as all years of Kawasaki SXR and Yamaha Super Jet. Length: 25ft

Part Number: 04-02-307

Hydro-Turf Mounting Blocks can be used for a variety of applications including: handle pole pads / lifters, footholds and mounting exhausts. Blocks are 2" thick (4.7" x 5.1"). Add 3M self-adhesive for $5.

Use Hydro-Turf 2 inch Rear Corner Kicks for added Feel and Control. Installs under foam or stitched mats (some models of watercraft may require an extended bottom mat).

Part Number: 04-02-348

Hydro-Turf Mounting Blocks can be used for a variety of applications including: handle pole pads / lifters, footholds and mounting exhausts. Blocks are 4" thick (4.7" x 5.1"). Add 3M self-adhesive for $5.

The Blowsion Hood Bumper is a premium solution to prevent the Handle pole from contacting the hood. For Freestyle and Freeride Applications. Black Diamond. Includes 3M Adhesive Backing.

Part Number: 04-04-206

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.