Search results for 'Sxr 800'

Aftermarket Kawasaki Fuel Cap Gasket. Fits Kawasaki All Models Years 300 440 550 650 750 800 900 1100 STX-12F STX-15F SX-R 1500. Fits OEM Kawasaki and Blowsion Kawasaki Billet Fuel Caps. Replaces OEM Kawasaki PN# 11009-3020.

Part Number: 01-07-232

Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.

Genuine OEM Kawasaki Fuel Cap Gasket. Fits Kawasaki All Models Years 300 440 550 650 750 800 900 1100 STX-12F STX-15F SX-R 1500. Fits OEM Kawasaki and Blowsion Kawasaki Billet Fuel Caps.

Part Number: 11009-3020

Blowsion Pro Water Bypass Fittings increase engine performance by diverting some of the water from the cylinder head to the bypass fitting, rather than forcing all of the water through the exhaust system. Fits 3/8" ID Cooling Hoses.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

The Blowsion Hood Bumper is a premium solution to prevent the Handle pole from contacting the hood. For Freestyle and Freeride Applications. Black Diamond. Includes 3M Adhesive Backing.

Part Number: 04-04-206

Hydro-Turf Mounting Blocks can be used for a variety of applications including: handle pole pads / lifters, footholds and mounting exhausts. Blocks are 4" thick (4.7" x 5.1"). Add 3M self-adhesive for $5.

Use Hydro-Turf 2 inch Rear Corner Kicks for added Feel and Control. Installs under foam or stitched mats (some models of watercraft may require an extended bottom mat).

Part Number: 04-02-348

Hydro-Turf Mounting Blocks can be used for a variety of applications including: handle pole pads / lifters, footholds and mounting exhausts. Blocks are 2" thick (4.7" x 5.1"). Add 3M self-adhesive for $5.

Add a kick tail to your watercraft bottom mat area with this 2" kick wedge. Helps to keep the riders back foot from slipping out of the tray and getting weight farther forward.

Part Number: 04-02-344

Dual Layer 2-Tone Sheets of 1/4" (6mm) Hydro-Turf with Cut Waffle Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.

Blowsion Billet Strap Hook Base. With the ever evolving aftermarket hulls and different engine configurations available in today's market the Blowsion Mechanic team consistently ran into problems with having to relocate individual components E.G Exhaust, Battery and Mounting Straps etc... So they went to work and designed a Billet Aluminum Strap Hook Base. Available in all colors! Strap Hook Sold Separately.

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Dual Color Sheets of 1/4" (5.5mm) Hydro-Turf with Cut Diamond Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.

48" x 17.5" section of 18mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.

Part Number: 04-02-331