Search results for 'Kawasaki'

Dual Layer 2-Tone Sheets of 1/4" (6mm) Hydro-Turf with Cut Waffle Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.

Billet Dash Plate Rotary Bilge Switch. Direct replacement for Kawasaki OEM plastic dash plates. Brushed finish. Bright dip anodized.

Part Number: 04-03-304

Genuine OEM Kawasaki Hood Latch Assembly for all Kawasaki 650SX, 750SX, SXR 800 and SXR 1500 Models.

Part Number: 27016-3703

Glue On! Includes bottom, sides, dash and undermat foam. Fits all years Kawasaki SXR 1500 Models. Requires Contact Cement/Blowsion Mat Glue for installation. Not available with 3M Self-Adhesive.

Part Number: 04-02-146

Blowsion Billet Strap Hook Base. With the ever evolving aftermarket hulls and different engine configurations available in today's market the Blowsion Mechanic team consistently ran into problems with having to relocate individual components E.G Exhaust, Battery and Mounting Straps etc... So they went to work and designed a Billet Aluminum Strap Hook Base. Available in all colors! Strap Hook Sold Separately.

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

The RRP Adjustable Hood Latch is made from billet aluminium 6061 t6. This adjustable hood latch gives you the possibility to adjust the amount of pressure applied on the hood seal in a second. Extremely strong design eliminating failure of the latch and danger of losing hood and the ability of sinking the ski. Available in Red, Black, Blue, Green.

NEW Blowsion Kawasaki Flanged Model. A simple installation drain valve alternative for the OEM drain plugs in Kawasaki model Watercraft. Color: Anodized Black. Sold Each.

Part Number: 06-01-068 Learn More

Dual Color Sheets of 1/4" (5.5mm) Hydro-Turf with Cut Diamond Grooves. Available in any two of the color combinations Hydro Turf offers on the below drop down menus.

See our special formulated solvent-based Mat Glue for Installation.

48" x 17.5" section of 18mm thick plush (softer) foam undermat. This our softest underpad. PLUSH offers greater comfort and compression recovery for extreme riders.

Part Number: 04-02-331

Genuine OEM Kawasaki Replacement Hood Seal for all 1992-2002 Kawasaki 750SX, SXI and SXi-Pro Models. This direct replacement hood seal is the strongest and most durable seal available.

Part Number: 39145-3731

Genuine OEM Kawasaki Replacement Hood Seal for all years Kawasaki SXR 800. This direct replacement hood seal is the strongest and most durable seal available.

Part Number: 39145-3781

Inexpensive traction option. Gain control of your ski or runabout by applying these lifter wedges to your tray sides or inner and outer gunnels. Available in two length options. Sold as Pair (2). Color: Black

Frogzskin woven water screens are the latest intuitive technology answer in the constant horsepower battle between today's high performance engines requiring more and more air, yet still keeping out the resulting ingress of destructive salt and fresh water! Kawasaki Ultra 250, Ultra 260 and Ultra LX Vent Kit (4 pieces). '07-'10

Part Number: 04-04-406