Search results for 'pump'

WSM Aftermarket Pump Rebuild Kit for Kawasaki 650, 750 and SXR 800 Models. Manufactured to OEM specifications. Kit includes replacements for the following OEM Kawasaki PN#'s 92049-3714 (QTY: 2), 92055-1021 (QTY: 2), 92045-3746 (QTY: 2), 92055-3706 (QTY: 1).

Part Number: 003-607

WSM Aftermarket Pump Trim Seal for Kawasaki 650, 750, SXR 800 and STX 900 Models. Manufactured to OEM specifications. Replaces OEM Kawasaki PN# 39145-3732.

Part Number: 003-550

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-106

Genuine Mikuni Replacement Pump Cover for Mikuni SBN Carburetors. Available in Black or Silver.

The *ORIGINAL* Impros Hooker 140mm impeller for the Kawasaki 650 140mm pump is a 3-blade large hub diameter, radial edge design rec finished stainless steel impeller designed and intended for Bottom end and “Hook up” for Freestyle and Freeriders on a 650 that utilizes the 140mm pump and want maximum AIR for tricks.

Genuine OEM Kawasaki Jet Pump Impeller Shaft. Fits all Kawasaki 650 SX, X2, 750 SX, 750 SXI, 750 SXI-PRO and 800 SXR Models. See complete list below for model fitment.

Part Number: 13107-3721

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

Genuine OEM Kawasaki Pump Rebuild Kit for 650, 750 and SXR 800 Models.

Part Number: 02-02-483

Genuine Mikuni Pop-Off Pressure Gauge 30PSI. Gauge gives accurate pop-off pressure readings. This high pressure pump is durable and easy to use. A must have tool for tuning your carbs.

Part Number: 06-04-012

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Designed with the freestyler in mind, the freestyle pump cone allows the engine to rev faster for the big tricks. Fits all years Kawasaki SXR, 750SX, SXI, SXi-Pro, X2 and 650SX Models.

Part Number: 02-02-405

Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!

Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.

Part Number: 06-01-311

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302