Search results for 'bilge'

The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-106

Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

Billet Dash Plate Rotary Bilge Switch. Direct replacement for Kawasaki OEM plastic dash plates. Brushed finish. Bright dip anodized.

Part Number: 04-03-304

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.

Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-418

Replacement OEM bullet connectors now available at Blowsion. Kit includes 5 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

Part Number: 01-04-417

Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.

Part Number: 06-01-201

Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

Part Number: 06-01-212

This Sano Bilge Switch Mounts Directly to the Bottom of the OEM Start / Stop Switch Housing on most Kawasaki Watercraft. Does not work on JS300, JS650 or X2 models.

Part Number: 06-01-213

Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.

Part Number: 06-01-215

Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.

Part Number: 06-01-311

Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-102

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301