Search results for 'bilge'
-
Blowsion Dash Fitting
Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.
Learn More -
Bilge Fitting Pro
Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.
Learn More -
Bilge Pump - Rule - 500GPH Automatic
Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.
Part Number: 06-01-002
Learn More -
Recessed Dash Mount
New! Blowsion Recessed Dash Mount. Fed up of breaking expensive Bilge Switches and Primer Bulbs? The Blowsion Team has a solution. The Recessed Dash Mount is perfect for mounting your switches and primers. The Mount enables the switch/primer to sit flush eliminating the risk of being knocked off. On top of that each mount comes with a Brushed Aluminum Anodized Bezel available in 5 color options. Stainless Steel Mounting Hardware and Installation Instructions Included.
Learn More -
OEM Bullet Terminals - 20 Pack
Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.
Part Number: 01-04-418
Learn More -
OEM Bullet Terminals - 5 Pack
Replacement OEM bullet connectors now available at Blowsion. Kit includes 5 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.
Part Number: 01-04-417
Learn More -
Bilge Switch / Primer Mounting Plate
This cool universal anodized black aluminum mounting plate allows easy mounting of the rotary bilge switch as well as primer bulb on the dash. Specifically designed for the SXR but will work with other models. Inside mounting with the correct bulb style primer hole and rotary bilge switch ID means a sanitary install in minutes with no grinders or tubes of silicone needed.
Part Number: 04-06-002
Learn More -
Rotary Bilge Switch - 3 Position
Blowsion Rotary waterproof bilge switches are corrosion resistant and have withstood the most abuse we can give them. Pair with the Blowsion Dash Fitting for best protection.
Part Number: 06-01-201
Learn More -
Bilge Switch - Handlebar Mount - Universal
Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.
Part Number: 06-01-212
Learn More -
Bilge Switch - Start Stop Switch Mount - Kawasaki
This Sano Bilge Switch Mounts Directly to the Bottom of the OEM Start / Stop Switch Housing on most Kawasaki Watercraft. Does not work on JS300, JS650 or X2 models.
Part Number: 06-01-213
Learn More -
Bilge Switch Replacement - 9ft Wire
Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.
Part Number: 06-01-215
Learn More -
Rule Bilge Pump Strainer Base
Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.
Part Number: 06-01-311
Learn More -
Bilge Pump Single Mount - Kawasaki
Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-102
Learn More -
Bilge Pump Hose - 3FT
Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-301
Learn More -
Bilge Pump Hose - 10FT
Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.
Part Number: 06-01-302
Learn More -
Bilge Pump Dual Mount - Kawasaki
Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.
Part Number: 06-01-101
Learn More