Search results for 'pump'

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001

Dual bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pumps within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-101

Blowsion Dual Bilge Pump Mounting Bracket. The bracket locates the pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. Fits 1994 and up Yamaha Superjet Models. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-153

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Single bilge pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. Single pump mounting bracket for Kawasaki Sxi Pro and KAWASAKI SXR 800. The bracket locates the pump within millimeters from the base of the KAWI hull. Easy built in installation, no messy adhesives. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-102

Single bilge pump mounting bracket for all 1994 and newer Yamaha SuperJet Models. The bracket locates the bilge pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-152

Replacement Fuel Resistant Rule Bilge Pump Strainer Base. Compatible with All Rule 360-1100GPH Models.

Part Number: 06-01-311

Blowsion Aluminum Pump Shoe for Yamaha 144mm Pumps. Replace that easily broken OEM plastic intake duct with this unbreakable aluminum replacement. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Polaris Octane and Rickters. Mounting holes are not drilled or tapped so install in the different Yamaha design aftermarket hulls can be facilitated.

Part Number: 02-02-432

Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.

Part Number: 01-02-557

Blowsion Billet Trim Lever - Left hand operated spring loaded trim lever for pump freestyle/freeride tilt or racing trim systems. Ergonomically designed for premium fit and feel whether you are on the waves or on the buoys. Now available in all colors!

Jet Dynamics 155mm over-sized aluminum replacement intake duct. Fits all years Yamaha Superjet, 1993-1996 WaveBlaster 1, Rickter and many other popular Yamaha based aftermarket hulls. *Intended for Use with Larger 155mm Yamaha Pumps.

Part Number: 02-05-432

Jet Dynamics Intake Grate for 1990-2007 Yamaha Superjet Models. The best scoop grate on the market for clawing the maximum amount of water into the thirsty Super Jet and WaveBlaster 1 pump.

Part Number: 02-01-153