Bilge Accessories

Items 1 to 16 of 21 total

per page

Page:
  1. 1
  2. 2
  • Bilge Pump - Rule - 500GPH

    Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

    Part Number: 06-01-001

    Learn More
    $34.95

  • Bilge Pump - Rule - 500GPH Automatic

    Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

    Part Number: 06-01-002

    Learn More
    $99.99

  • Bilge Pump Hose - 10FT

    Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

    Part Number: 06-01-302

    Learn More
    $23.00

  • Bilge Pump Hose - 3FT

    Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

    Part Number: 06-01-301

    Learn More
    $7.00

  • Bilge Pump Mount - Kawasaki 550/650/750SX

    The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki 550SX, 650SX and 750SX Models. Material: Aluminum. Color: Anodized Black.

    Part Number: 06-01-106

    Learn More
    $29.95

  • Bilge Pump Mount - Kawasaki JS440/550

    The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki JS440 and JS550 Models. Material: Aluminum. Color: Anodized Black.

    Part Number: 06-01-105

    Learn More
    $29.95

  • Bilge Pump Mount - Kawasaki SXR 1500

    The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). The bracket mounts to the lower two bolts of the driveshaft bearing carrier. Includes rivets to mount bilge pump strainer to bracket. Fits all Kawasaki SXR 1500 Models. Material: Aluminum. Color: Anodized Black.

    Part Number: 06-01-104

    Learn More
    $29.95

  • Bilge Pump Mount - Yamaha WaveBlaster

    The Blowsion Bilge Pump Mount is designed to mount the Rule Bilge Pump (Sold Separately). Includes rivets to mount bilge pump strainer to bracket. Fits 1993-1996 Yamaha WaveBlaster 1 Models. Material: Aluminum. Color: Anodized Black.

    Part Number: 06-01-107

    Learn More
    $29.95

  • Bilge Switch / Primer Mounting Plate

    This cool universal anodized black aluminum mounting plate allows easy mounting of the rotary bilge switch as well as primer bulb on the dash. Specifically designed for the SXR but will work with other models. Inside mounting with the correct bulb style primer hole and rotary bilge switch ID means a sanitary install in minutes with no grinders or tubes of silicone needed.

    Part Number: 04-06-002

    Learn More
    $11.50

  • CAS Billet Aluminum Flange Only

    Available for riders wanting to use the end flange only for custom scupper and rear exhaust installations etc. The new billet flange assembly is the premium design setup and allows use of the Blowsion billet exhaust outlet so vain riders can sanitize both sides of the rear of their watercraft. Fits all years Super Jet, KAWI 750 and SXR 800, KAWI 650, and Polaris Octane. Anodized Clear.

    Part Number: 06-01-023

    Learn More
    $99.15

  • Duckbill One Way - Kawasaki

    Billet SXR Duckbill- eliminates water via the OEM Kawi SXR drain plug orifice at the rear of the ski. This is the most economical way to keep the SXR engine compartment dry. Not a cheap universal mount, this drain bladder is billet and designed specifically for the Kawasaki SXR 800.

    Part Number: 06-01-015

    Learn More
    $49.40

  • Duckbill One Way - Replacement

    Replaces your worn out rubber duckbill. Includes color-matched Zip Tie.

    Part Number: 06-01-010

    Learn More
    $23.50

  • Expanding Foam (2 Part) - Pint Kit

    No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.

    Part Number: 06-03-131

    Learn More
    $54.95

  • Expanding Foam (2 Part) - Quart Kit

    No more home insulation foam in a can. This is the real deal. Marine quality expanding foam. Mix equal parts A and B in the supplied mixing cups and you have waterproof and cured foam expanding in 60 seconds or less.

    Part Number: 06-03-132

    Learn More
    $69.95

  • OEM Bullet Terminals - 20 Pack

    Replacement OEM bullet connectors now available at Blowsion. Kit includes 20 Male and Female terminals with Insulators. Perfect for those super sanitary bilge kit installations or replacements for Electrical box connections.

    Part Number: 01-04-418

    Learn More
    $21.95

  • RRP Scupper Valve

    RRP Scupper Valve Replacement. Complete Assembly.

    Part Number: 06-01-030

    Learn More
    $79.00

Items 1 to 16 of 21 total

per page

Page:
  1. 1
  2. 2